1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Ultimate mounting for Scangauge II.

Discussion in 'Gen 2 Prius Accessories & Modifications' started by adric22, Nov 11, 2010.

  1. adric22

    adric22 Ev and Hybrid Enthusiast

    Joined:
    Apr 6, 2009
    642
    144
    2
    Location:
    Fort Worth, TX
    Vehicle:
    2018 Chevy Volt
    Model:
    Plug-in Advanced
    Took me about an hour with a dremel, but I think it came out fantastic. It is right behind the steering wheel so you look through the wheel to see the screen. Granted, it is a bit hard to press the buttons, but I generally leave it on the same screen.

    [​IMG]
    [​IMG]
     
    #1 adric22, Nov 11, 2010
    1 person likes this.
  2. biff_debris

    biff_debris WOOF!

    Joined:
    May 8, 2005
    81
    2
    0
    Location:
    Prescott, WA
    Vehicle:
    2005 Prius
    Nicely done! Mine is still Velcro'd way down low below the radio.
     
    #2 biff_debris, Nov 11, 2010
  3. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    110,133
    50,050
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    that's purdy!:)
     
    #3 bisco, Nov 11, 2010
  4. xs650

    xs650 Senior Member

    Joined:
    Jul 2, 2010
    4,539
    1,433
    9
    Location:
    Northern California
    Vehicle:
    2010 Prius
    Model:
    II
    Nice work, how did you get the rounded edges on the opening?
     
    #4 xs650, Nov 11, 2010
  5. MJFrog

    MJFrog Active Member

    Joined:
    Jul 21, 2009
    780
    266
    0
    Location:
    NE Oklahoma
    Vehicle:
    2018 Nissan LEAF
    Model:
    N/A
    That's pretty much where I have mine velcro'd. I don't want a permanent installation as my wife has a Prius too and we use her's for LD trips. This way, I can move it from my car to her's with little trouble. It DOES look nice though.

    Yeah, pushing the buttons is a pain...I leave mine pretty much set at:
    RPM - check if/how hard the engine is running
    soc - always want to know how much charge is in the HV battery
    bta - I have an Enginer kit and I monitor how many amps go to HV battery
    fWT - Nice to know when I'm warmed up, near/in S4.
     
    #5 MJFrog, Nov 11, 2010
  6. adric22

    adric22 Ev and Hybrid Enthusiast

    Joined:
    Apr 6, 2009
    642
    144
    2
    Location:
    Fort Worth, TX
    Vehicle:
    2018 Chevy Volt
    Model:
    Plug-in Advanced
    I use 3 of the same readouts (I also have an engineer kit) but I see no point in SOC since I can see that on the center screen in the prius. So I use RPM,engine temp, bat volts, bat amps.
     
    #6 adric22, Nov 11, 2010
  7. KK6PD

    KK6PD _ . _ . / _ _ . _

    Joined:
    Mar 24, 2008
    4,003
    946
    118
    Location:
    Los Angeles Foothills
    Vehicle:
    Other Hybrid
    Model:
    N/A
    +1

    That is just some fine Dremel work!!!
    I have always considered that spot, excuse me if I borrow your idea!

    Well done!!!
     
    #7 KK6PD, Nov 11, 2010
  8. don_chuwish

    don_chuwish Well Seasoned Member

    Joined:
    May 1, 2009
    816
    182
    0
    Location:
    Southern Oregon
    Vehicle:
    2007 Prius
    Model:
    II
    That really is slick. I assume the viewing angle is OK? How about glare problems in bright sun?

    - D
     
    #8 don_chuwish, Nov 15, 2010
  9. Crazyhorse6901

    Crazyhorse6901 New Member

    Joined:
    Jun 21, 2009
    114
    9
    10
    Location:
    Hampton,VA
    Vehicle:
    2010 Prius
    Model:
    IV
    Nice job with the install, looks great...
     
    #9 Crazyhorse6901, Nov 16, 2010
  10. patsparks

    patsparks An Aussie perspective

    Joined:
    Jul 12, 2007
    10,664
    567
    0
    Location:
    Adelaide South Australia
    Vehicle:
    2004 Prius
    Model:
    N/A
    Where is the like button on PriusChat? I like it!

    Mine is velcroed to the top of the steering column.
     
    #10 patsparks, Nov 16, 2010
  11. Azipod

    Azipod Member

    Joined:
    Aug 25, 2010
    139
    21
    0
    Location:
    NorCal
    Vehicle:
    2007 Prius
    Model:
    N/A
    Very nice! Are you willing to cut panels for a fee? I'm trying to find a good place to mount my SG as well -- so far I'm thinking about the CD panel.
     
    #11 Azipod, Nov 22, 2010
  12. UGC

    UGC Member

    Joined:
    Jul 25, 2009
    162
    37
    0
    Location:
    USA
    Vehicle:
    2013 Prius
    Model:
    Persona
    +1, also, how did you cut the perfect square? I have a dremel tool, but would not trust myself to get it right the first try.

    Any recommendations? Thanks.
     
    #12 UGC, Nov 29, 2010
  13. JimN

    JimN Let the games begin!

    Joined:
    Nov 26, 2006
    7,028
    1,116
    0
    Location:
    South Jersey
    Vehicle:
    2010 Prius
    Model:
    V
    Excellent job.
     
    #13 JimN, Nov 29, 2010
  14. NoMoShocks

    NoMoShocks Electrical Engineer

    Joined:
    Jan 21, 2007
    1,292
    82
    11
    Location:
    Camas, WA
    Vehicle:
    2010 Prius
    Model:
    IV
    No problem, for your next dremel project, you can create a five button remote control panel to fit in one of the spare swich locations.
     

    Attached Files:

    #14 NoMoShocks, Dec 3, 2010
  15. SageBrush

    SageBrush Senior Member

    Joined:
    Jun 4, 2008
    11,627
    2,531
    8
    Location:
    Southwest Colorado
    Vehicle:
    2012 Prius v wagon
    Model:
    Two
    Nice job!
    What stops the gauge from falling into the dash ?
     
    #15 SageBrush, Dec 3, 2010
(You must log in or sign up to post here.)