1. Attachments are working again! Check out this thread for more details and to report any other bugs.

P0a80 won't reset after reconditioning.

Discussion in 'Prius c Technical Discussion' started by 2014priuscphil, Jun 24, 2021.

Tags:
  1. 2014priuscphil

    2014priuscphil New Member

    Joined:
    Jun 24, 2021
    3
    2
    0
    Location:
    Texas
    Vehicle:
    2014 Prius c
    Model:
    III
    I have a 2014 prius c three. I got the p0a80 code. I pulled the battery out and reconditioned the modules. One was bad and I replaced it. I balanced all the cells by hooking them in parallel and letting it sit for 24 hours. I put it back in and it won't start throwing the p0a80 code again and again. I disconnect the 12 volts power each time for 5 minutes to reset the code and clear it with the dr prius app. I let it sit overnight and still the same thing this morning. All the voltages are within .15 volts. A couple of times it threw p0adc, p0ae0, p0ae7 also. Those are relay related codes. It only threw those a couple of times and there not currently up. Any advise would be great. I need to get my car going.
     

    Attached Files:

    #1 2014priuscphil, Jun 24, 2021
  2. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    110,129
    50,045
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    are you reading the voltages under load?
     
    #2 bisco, Jun 25, 2021
  3. 2014priuscphil

    2014priuscphil New Member

    Joined:
    Jun 24, 2021
    3
    2
    0
    Location:
    Texas
    Vehicle:
    2014 Prius c
    Model:
    III
    Yes during reconditioning I pulled each module down to 2.5 volts at .5 amp draw. All of them charged back up to 5000 mah at least. After the billionth time of disconnecting the 12 volt system and waiting 5 minutes to clear the codes, I left the 12 volt on. I just happened to try and start it hours later and it started. I have 50 miles down and the p0a80 has disappeared. It’s running great.
     
    #3 2014priuscphil, Jun 25, 2021
    bisco and SFO like this.
  4. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    110,129
    50,045
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    congrats!(y)
     
    #4 bisco, Jun 25, 2021
  5. Gio syl

    Gio syl Junior Member

    Joined:
    Apr 10, 2020
    7
    1
    0
    Location:
    USA
    Vehicle:
    2013 Prius c
    Model:
    ----USA----
    I'm trying to recondition my pack ....can u tell me what tools was used to recondition your pack .....and how u was able to check the capacity of the modules....
    Also when doing the process do you disconnect the 12volts battery and how long do you leave the high voltage battery for between charge and discharge
     
    #5 Gio syl, Jul 27, 2021
  6. 2014priuscphil

    2014priuscphil New Member

    Joined:
    Jun 24, 2021
    3
    2
    0
    Location:
    Texas
    Vehicle:
    2014 Prius c
    Model:
    III
    Howdy
    I used a Tenergy T-180.



    I wasted a lot of time with bad information from youtube videos. Several indicate pulling down the cells to 6-6.3 volts I did this many cycles with limited success. I found a military document indicating to pull the cells down to 40% of nominal voltage. I found a video about using a prolong setup to recondition the entire pack. I grabbed the numbers off of it. Prolong pulls the battery down to 60% of nominal voltage then charge back up. Then pull it down to 50% and charge back up. And finally pull it down to 40% and charge back up.



    The nominal voltage of the cell is 7.2 volts. 1st I discharged it at a rate .5 amps down to 4.3 volts. I charged it fully at a rate of 1 amp. 2nd I discharged it at a rate of .5 amps down to 3.6 volts. I charged it fully at a rate of 1 amp. 3rd I discharged it at a rate of .5 amps to 2.9 volts. I charged it fully at a rate of 1 amp. This procedure worked great returning the cells to full capacity.

    I had one T-180 charger and this took forever, but it worked. I'm simply going to buy the Prolong setup now.
     
    #6 2014priuscphil, Jul 27, 2021
  7. tracy ing

    tracy ing Active Member

    Joined:
    Dec 22, 2017
    384
    168
    0
    Location:
    wash dc
    Vehicle:
    2005 Prius
    Model:
    N/A
    What is the rationale for the low amp charge discharge rates ?
    I have been doing this to these batteries for over 10 years now at 1C 6.5 amps up and down (no lower than 6volts and let it delta as high a voltage as they want, my delta is 400 mv.), restores them just fine
    I never found any benefit at all to lower amp rates, does anyone have any data that shows it is supposed to or did ?
    Prius cell powered honda insight






    my street cred
    anyhow, serious about does anyone have any data supporting these lower charge discharge rates and restoration to full capacity ?
     
    #7 tracy ing, Jun 12, 2022
    Last edited: Jun 12, 2022
  8. mr_guy_mann

    mr_guy_mann Senior Member

    Joined:
    Sep 3, 2020
    3,668
    1,715
    0
    Location:
    NJ-USA
    Vehicle:
    2006 Prius
    Model:
    Four
    Almost all inexpensive hobby chargers can only dissipate 5 or 10 watts when discharging. That and most folks are cautious when exceeding the normal "in use" voltage range.

    If your experience shows good results with more aggressive amperage rates, then great.

    Posted via the PriusChat mobile app.
     
    #8 mr_guy_mann, Jul 13, 2022
(You must log in or sign up to post here.)