1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Liftgate- broken interior handle

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by southtxprius, Jul 22, 2015.

  1. southtxprius

    southtxprius Junior Member

    Joined:
    Dec 3, 2014
    78
    9
    0
    Location:
    South TX
    Vehicle:
    2010 Prius
    Model:
    II
    Hello,

    One of the interior handles for the liftgate broke off. I removed it. From what I can tell, this handle is molded to the interior trim part.

    I'd like to glue this piece back on, rather than having to purchase the complete lower trim piece.

    Any suggestions on the best type of glue for this plastic? Thanks! DSCF4407.jpg
     
    #1 southtxprius, Jul 22, 2015
  2. David Beale

    David Beale Senior Member

    Joined:
    Jul 24, 2006
    5,963
    1,985
    0
    Location:
    Edmonton Alberta
    Vehicle:
    2012 Prius
    Probably ABS. Get ABS glue from the plumbing section of the Home Store.
     
    #2 David Beale, Jul 22, 2015
  3. southtxprius

    southtxprius Junior Member

    Joined:
    Dec 3, 2014
    78
    9
    0
    Location:
    South TX
    Vehicle:
    2010 Prius
    Model:
    II
    It's difficult to see in the photo, but below the RH (right hand side) raised lettering is this: PP/PE. Could this stand for a mix of polypropylene and polyethylene?
     
    #3 southtxprius, Jul 23, 2015
  4. southtxprius

    southtxprius Junior Member

    Joined:
    Dec 3, 2014
    78
    9
    0
    Location:
    South TX
    Vehicle:
    2010 Prius
    Model:
    II
    Bump. Any other thoughts re: glue for this type of plastic?
     
    #4 southtxprius, Jul 27, 2015
  5. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    110,137
    50,052
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    maybe try a simple plastic glue from the hardware store, like model airplane glue.
     
    #5 bisco, Jul 27, 2015
  6. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,678
    39,222
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    Test glues? Put a drop somewhere on the inside of the piece, maybe try bonding some scrap plastic to it?

    When you first posted I had to pull out the trim a bit on ours, had a look. Definitely just welded somehow, glue or heat.
     
    #6 Mendel Leisk, Jul 27, 2015
  7. southtxprius

    southtxprius Junior Member

    Joined:
    Dec 3, 2014
    78
    9
    0
    Location:
    South TX
    Vehicle:
    2010 Prius
    Model:
    II
    I'll give it a shot. Thanks!
     
    #7 southtxprius, Jul 27, 2015
  8. Akramahmad1

    Akramahmad1 New Member

    Joined:
    Feb 9, 2021
    2
    0
    0
    Location:
    California
    Vehicle:
    2007 Prius
    Model:
    N/A
    I have the same thing with my 07 Prius the whole lift gate was broken two times until I used loctite super glue then loctite epoxy, the main thing help me prevent the liftgate from being such weak is a handle I used to support, check this video:

     
    #8 Akramahmad1, Feb 9, 2021
(You must log in or sign up to post here.)