Jacking / Lifting points on your Prius

Have you seen anyone mention making or buying the rubber blocks as shown in the illustration? I haven't. I did note that John1701a has a writeup for changing the oil, and he placed the jack and jack stand(s) in different locations than shown in the illustration.

My GF has an Avalon, and it has a similar illustration. The locations for the jack stands are basically the same as the Prius; there is a flange that has notches where you are supposed to place the jack stands. I used these locations when I changed the oil, but having always worked on trucks that have a full frame, it gives me the hebeejeebes to support half of the vehicle weight on the body. When I did the front brakes another time, I supported the car under the front subframe, which seems to be more secure to me.

I watched the tech who checked my alignment (for the 4th time, see this thread) and I watched as he lifted the vehicle briefly to set the targets on the wheels; he placed the lift blocks under the shock mounts on the rear, I couldn't see exactly where he set them in the front, but it was up near the front wheels, probably under the subframe.

 

<div class='quotetop'>QUOTE(FloridaWen @ Jul 23 2007, 07:51 AM) [snapback]483570[/snapback]</div>

I was asking in the context of a DIY user at home, using commonly available jacks and jack stands. I haven't done an exhaustive search, but I haven't seen anything like that for sale. I'm considering making my own, but I don't know if I will have time to do it. I would buy them if they were reasonable cost.

 

<div class='quotetop'>QUOTE(FloridaWen @ Jul 23 2007, 09:55 AM) [snapback]483621[/snapback]</div>

I remember the coil spring expanders, but haven't seen them for sale lately. Maybe a JC Whitney item? The only problem with that is that I will get catalogs mailed to me for the next 5 years. :lol:

I found this:

http://www.harborfreight.com/cpi/ctaf/disp...temnumber=36004

We have a couple of Harbor Freight stores nearby, so I may try to find this when I get a chance. It may not be thick enough for the groove, I will need to measure the flange.

Not sure about the 3m sanding block; good thinking out of the box though.

 

Oh yeah, I was going to point this out earlier, but forgot:

There is a typo under Jack Position:

Rear: Differential Carrier

There is no differential at the rear (unless you have the special 4wd version of the Prius).

There is a pedestal that is located about where the rear differential carrier would be. I'm pretty sure that is the jacking point for the rear.

 

<div class='quotetop'>QUOTE(dogfriend @ Jul 23 2007, 09:11 AM) [snapback]483558[/snapback]</div>

I use the points shown in the diagram you provided with my floor jack.

I simply used the sole of an old sandal that's about 3/8" thick. I bet an old zori would work as well.

The load isn't that much to raise one wheel.

glenk

 

Heck, 'ol piece a 2x4 works fine.
Yee Ha

 

Here's an interesting product I found discussed on a VW board:

http://www.eastwoodco.com/jump.jsp?itemID=...temType=PRODUCT

I also found the "2 x 4" solution:

 

<div class='quotetop'>QUOTE(FloridaWen @ Jul 24 2007, 06:42 AM) [snapback]484083[/snapback]</div>

Yeah, I'm wary of the 2 x 4 / 2 x 6 splitting in half while on top of the jack stand. Fabricating something out of a couple of pieces of 3/4" plywood might be a better idea; the crossply construction of the plywood will make it a lot less likely to split.

You should always try to make the jack stands as secure as possible; you never know what may happen:

http://www.explorerforum.com/forums/showpo...mp;postcount=49

 

<div class='quotetop'>QUOTE(FloridaWen @ Jul 24 2007, 07:07 AM) [snapback]484098[/snapback]</div>

Actually, you can see it without getting under the car.

If you go to toyota.com, click on 360° views, supersize the car and rotate:


[attachmentid=10086]

In this view, I circled what I believe are the center jacking points in red:

[attachmentid=10087]

 

<div class='quotetop'>QUOTE(dogfriend @ Jul 24 2007, 03:48 PM) [snapback]484302[/snapback]</div>

Very funny and I just hope no one takes you seriously!

Especially during an earthquake!..ROTFLMAO!

 

<div class='quotetop'>QUOTE(eastender43 @ Jul 26 2007, 09:46 AM) [snapback]485498[/snapback]</div>

Swear to whatever deity you choose to worship, the story about the truck on jackstands during the Loma Prieta is 100% true.

Also, I am serious about the center jacking points, but I'm not sure about the front one; the manual seems to locate it further back. I circled the part that bolts the lower engine/ transaxle to the subframe.

 

<div class='quotetop'>QUOTE(FloridaWen @ Jul 26 2007, 12:59 PM) [snapback]485633[/snapback]</div>

Yes, I think you are correct. I thought I saw a thread where someone used the motor mount, but what you are calling the "K member" (I'm calling it the subframe) is probably best and corresponds to the drawing in your first post.

 

Yeah now I get it ,My Bad!

I thought you were suggesting using those two jacking points to BALANCE the car while you VERY carefully worked under it...

I believe your earthquake story...I saw a photo of a guy who had his 4x4 pickup tipped 45 degrees,and held up by a single 2x8....and he was under it working on it....pretty nutty....



<div class='quotetop'>QUOTE(dogfriend @ Jul 26 2007, 04:43 PM) [snapback]485715[/snapback]</div>

 

<div class='quotetop'>QUOTE(eastender43 @ Jul 26 2007, 07:01 PM) [snapback]485878[/snapback]</div>

Oh, its completely safe, he has a backup 2 x 4 near the front:


[attachmentid=10183]

Here's a safer way:


[attachmentid=10184]