2007 taillight,Back up,indicator bulbs,???

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by eastender43, Jul 26, 2007.

  1. eastender43

    eastender43 Junior Member

    Joined:
    Jul 17, 2007
    21
    3
    0
    All my bulbs got crunched,I have the new taillight bodies,and went to get bulbs...

    To my surprise,No one lists anything for the 2007 Prius!....!I have searched everywhere online....even the owners manual is vague...

    Does this mean you have to buy new bulbs from a genuine Toyota dealer?

    I commonly see a listing for the 2006,specifying Sylvania 2825 and 7440....but the brake light is listed as LED for the 2007....

    Does anyone know what commonly available bulbs will work in a 2007?

    Thanks very much!....Bob
     
    #1 eastender43, Jul 26, 2007
  2. BE55Roberts

    BE55Roberts New Member

    Joined:
    Jul 28, 2007
    2
    0
    0
    <div class='quotetop'>QUOTE(eastender43 @ Jul 26 2007, 11:54 AM) [snapback]485506[/snapback]</div>
    I understand that the lights are all LEDs. Hence, you won't find a specific bulb. The LEDs are an array of lights that you'll probably have to go to the dealer to get replaced. And be sure you got the right tail light bodies to go with your 2007 prius.
     
    #2 BE55Roberts, Jul 28, 2007
  3. Bill Merchant

    Bill Merchant absit invidia

    Joined:
    May 3, 2005
    4,096
    85
    13
    Location:
    USA | Oregon | Portland area | 97004 |
    Vehicle:
    2007 Prius
    The brake lights are LEDs and probably part of the back light housing assembly. The rear turn signal lamps are 992 (7440A). The tail light is 2825. The Back up light is 7440. Have I missed any?
     
    #3 Bill Merchant, Jul 30, 2007
  4. eastender43

    eastender43 Junior Member

    Joined:
    Jul 17, 2007
    21
    3
    0
    <div class='quotetop'>QUOTE(Bill Merchant @ Jul 30 2007, 12:57 AM) [snapback]487329[/snapback]</div>

    That is 100% correct Bill,Thanks!...Basically all the ones you can replace are same as the 2006...ie,7440 and 2825.....

    Got both taillight housings replaced easily enough,through the little access doors...Only tricky part is there are wire securing clips on the ends of the taillight studs....remove those, unscrew the 2 10mm nuts,and give a firm YANK to unclip the other 2 friction mounts,and that's it...

    On installation,When tightening the nuts ,only use very minimal torque(!/4 turn beyond handtight) or you can crack your new TL!...

    New baby looks sharp again with those snazzy rear taillights!!!
     
    #4 eastender43, Jul 30, 2007
  5. nerfer

    nerfer A young senior member

    Joined:
    Mar 1, 2006
    2,507
    237
    28
    Location:
    Chicagoland, IL, USA, Earth
    Vehicle:
    Other Hybrid
    Model:
    N/A
    <div class='quotetop'>QUOTE(eastender43 @ Jul 26 2007, 11:54 AM) [snapback]485506[/snapback]</div>
    Where did you get the taillight bodies? I need one too, and have been looking around a little...
     
    #5 nerfer, Aug 3, 2007
  6. eastender43

    eastender43 Junior Member

    Joined:
    Jul 17, 2007
    21
    3
    0
    <div class='quotetop'>QUOTE(nerfer @ Aug 2 2007, 11:00 PM) [snapback]489780[/snapback]</div>
    I got one on Ebay for $76 shipped,had a 3/4 crack in the very bottom,not an issue to me....
    Got one from a yard in MN....PAM auto supply..St Cloud.they still have a right one...$140 plus 17 shipping

    Danny on this site offered to get one for $162,plus shipping..

    Hoy-Fox also has a price of $164 for a new one.....

    Some salvage places want more than $165.And one on Ebay went for $174 yesterday...

    Man these things break very easily.....It's a shame they don't sell just the lens,but it is all glued together,obviously....They are pretty though....Good Luck,Bob
     
    #6 eastender43, Aug 3, 2007
  7. jump123

    jump123 New Member

    Joined:
    Feb 15, 2008
    30
    0
    0
    Location:
    new york
    Vehicle:
    2008 Prius
    I just noticed this morning that the clear plexiglass cover on my tail light assembly is cracked (badly! there's now a hole in it!). do i need to replace the whole assembly or can I just have the top/cover (the clear plexi part) replaced?
     
    #7 jump123, Feb 20, 2010
(You must log in or sign up to post here.)