1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Post Aftermarket Stereo Fiasco

Discussion in 'Gen 2 Prius Technical Discussion' started by Duncwarw, Jun 26, 2024.

  1. Duncwarw

    Duncwarw Junior Member

    Joined:
    Dec 6, 2017
    31
    7
    1
    Location:
    Capital Region, NY
    Vehicle:
    2008 Prius
    Model:
    N/A
    I feel that this issue should be separated from my other thread about my new stereo and bypassing the JVC thing.

    Once I finally got the new thing working, I still have the multiple warning lights on the dash but that's nothing new.
    My (yet another) issue is with the MFD,

    Symptoms:
    Climate; "Check the connection to the air conditioner"
    Audio: "Audio Off" (non-issue)
    Trip Info: No battery levels, no arrows
    Menu: "The external system is not connected"
    Dest: Same as "Menu"
    Map: Same as "Menu"

    I recently bought a virtually identical Prius to drive but I really need the '08 to work/pass inspection as it is my work vehicle.

    I don't think it's a bad MFD and I hope somebody can point me in a the right direction.

    Thanks!
     
  2. TMR-JWAP

    TMR-JWAP Senior Member

    Joined:
    Aug 12, 2016
    6,404
    6,062
    0
    Location:
    Columbia, SC
    Vehicle:
    2007 Prius
    Model:
    Touring
    What ever you did, the car is no longer communicating with the MFD.
    At a minimum, verify all your connections at the rear of the MFD have been plugged back in.
     
    Meg&Bear likes this.
  3. Duncwarw

    Duncwarw Junior Member

    Joined:
    Dec 6, 2017
    31
    7
    1
    Location:
    Capital Region, NY
    Vehicle:
    2008 Prius
    Model:
    N/A
    Thanks for the response. I'll look again.
    I don't think I unplugged anything from the MFD and I left the thing plugged in and just put the MFD aside
    while I worked on the stereo. I hope I missed another connector (or two) !
     
  4. Tombukt2

    Tombukt2 Senior Member

    Joined:
    Nov 29, 2020
    10,372
    1,791
    0
    Location:
    Durham NC
    Vehicle:
    2009 Prius
    Model:
    Base
    And have you cut into things or just tapped? Taking apart and soldered? But yeah you've definitely got to communication problem The plugs click in pretty smartly. And they can fail you for your MFD not working for inspection because I wouldn't think the check engine light would be lit for this reason.
     
    Meg&Bear likes this.
  5. dolj

    dolj Senior Member

    Joined:
    May 14, 2012
    7,854
    3,965
    0
    Location:
    Wellington, New Zealand
    Vehicle:
    2007 Prius
    Model:
    N/A
    Did the harness you used have an integrated 68Ω resistor within? If not search for 68 ohm resistor in the Audio and Accessories forum for threads that detail how to do that. The resistor is required to correctly terminate the comms bus.
     
    Meg&Bear likes this.
  6. Duncwarw

    Duncwarw Junior Member

    Joined:
    Dec 6, 2017
    31
    7
    1
    Location:
    Capital Region, NY
    Vehicle:
    2008 Prius
    Model:
    N/A
    Soldered and heat shrink(ed).
    Thanks for the hints, I've been really busy lately but I need to find time to get back to work on that Prius...
     
    Meg&Bear likes this.
  7. Duncwarw

    Duncwarw Junior Member

    Joined:
    Dec 6, 2017
    31
    7
    1
    Location:
    Capital Region, NY
    Vehicle:
    2008 Prius
    Model:
    N/A
    It came with the resistor. I'll solder it in.
    Thanks!
     
    Meg&Bear likes this.
  8. tkc100

    tkc100 Junior Member

    Joined:
    Jun 4, 2016
    61
    21
    0
    Location:
    Arizona
    Vehicle:
    2007 Prius
    Model:
    Two
    I have considered replacing my head unit and I know that it has been done successfully but.....
    While work on another problem I got an education on the CAN bus. There numerous control units and items that communicate over the bus. Any disruptions to the communications can have unexpected and seemly unrelated consequences.
     
    Meg&Bear likes this.