1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Has anyone replaced their brake actuator only to get P0a78-526 and other connector codes?

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by Mike from Merrick, Apr 30, 2023.

Page 2 of 2
  1. Mike from Merrick

    Mike from Merrick Junior Member

    Joined:
    Sep 9, 2022
    32
    4
    0
    Location:
    New York
    Vehicle:
    2014 Prius
    Model:
    V
    No, just the top cover. Each time taking careful consideration to all of the plugs inside of it.
     
    #21 Mike from Merrick, May 3, 2023
  2. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    24,904
    16,213
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    Hmm. I'm still thinking something probably happened to it in that activity.

    But sometimes it's easy to go back and figure out what, and sometimes it isn't.

    If you can, it helps with feeling confident you can avoid the same thing happening to a replacement one.
     
    #22 ChapmanF, May 3, 2023
    Mike from Merrick likes this.
  3. Mike from Merrick

    Mike from Merrick Junior Member

    Joined:
    Sep 9, 2022
    32
    4
    0
    Location:
    New York
    Vehicle:
    2014 Prius
    Model:
    V
    Right, I'm taking your advice and will re check all of the connections. The only other thing that might have happened, is when I first changed the brake actuator, and tried to add and bleed the inverter fluid, I discovered that the pump was not working. So I changed the inverter cooling pump while changing the brake actuator the 2nd time. Then added and bled the inverter fluid. My thinking is the car ran with it hot, but didn't throw a code due to it being driven like 5 miles in NYC (Brooklyn) where my daughter lives. SO when the fluid recirculated, possibly a crack in the inverter somewhere caused the red triangle, or maybe I watch too many videos....
     
    #23 Mike from Merrick, May 3, 2023
  4. Mike from Merrick

    Mike from Merrick Junior Member

    Joined:
    Sep 9, 2022
    32
    4
    0
    Location:
    New York
    Vehicle:
    2014 Prius
    Model:
    V
    Well, I installed the brake actuator, and newly purchased inverter, went into techstream and did the brake bleed, linear valve reset, zero and cleared the codes. After starting it and backing it up, I got the red triangle and c1364.
    Next day, went back out, cleared the codes, checked everything again, and was able to drive it around the block. No codes, no lights, no red triange. I must admit, I'm going to test drive it tomorrow for a good 1/2 hour or so, then see if I can consider this case closed.
     
    #24 Mike from Merrick, May 10, 2023
  5. Mike from Merrick

    Mike from Merrick Junior Member

    Joined:
    Sep 9, 2022
    32
    4
    0
    Location:
    New York
    Vehicle:
    2014 Prius
    Model:
    V
    C1364 comes up each time I start the Prius. I can delete the code with my scan tool, and drive it without any issues. Then, stop to get a coffee, turn it off, restart and c1364 appears again. Scan tool delete, off to the inspection station to get new annual NYS inspection. Only 1 monitor was ahowing, so it passed with no issues. Looks like another bad brake actuator, so off to ebay I go.....
     
    #25 Mike from Merrick, May 11, 2023
(You must log in or sign up to post here.)
Page 2 of 2