1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Replacing a power source ECU - how to?

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by benjita, Aug 6, 2011.

  1. benjita

    benjita Junior Member

    Joined:
    Oct 6, 2010
    41
    9
    0
    Location:
    Fairfax, VA
    Vehicle:
    2006 Prius
    Model:
    N/A
    Can anyone give me some idea as to where the power source ECU is located and how difficult it may be to switch out? Is this something that a non- Toyota mechanic could replace?

    Thanks!
     
    #1 benjita, Aug 6, 2011
  2. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,200
    6,482
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    The power source control ECU is located near the combination meter. I don't think it is very hard to replace. However it would probably be better to seek out a mechanic who specializes in Toyota vehicles to do that work - since that individual is more likely to have access to the required Toyota technical information.

    I am wondering how you came to the conclusion that the power source control ECU needs to be changed.
     
    #2 Patrick Wong, Aug 7, 2011
  3. benjita

    benjita Junior Member

    Joined:
    Oct 6, 2010
    41
    9
    0
    Location:
    Fairfax, VA
    Vehicle:
    2006 Prius
    Model:
    N/A
    A short from an audio input device connected to the rear of the radio caused the following things to stop working: MFD, clock, radio, side mirrors, power outlets. Toyota dealer thinks it is the Power ECU but want to charge $1200 to replace. I can pick up a used one for $150 but have no idea how to go about replacing it. Do you know if the Power ECU needs to be calibrated in anyway?
     
    #3 benjita, Aug 7, 2011
  4. seilerts

    seilerts Battery Curmudgeon

    Joined:
    Mar 7, 2010
    3,326
    1,513
    38
    Location:
    Santa Fe, NM
    Vehicle:
    2005 Prius
    If you are lucky, it may be that this can be accessed by pulling out the far left air duct, then the bottom and top panels that surround the steering column. Worst case would be removing the combination meter, which requires much more dash disassembly. Of course, you will need to disconnect 12V power, i.e. the battery negative cable.
     
    #4 seilerts, Aug 7, 2011
  5. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,200
    6,482
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    I suggest that you subscribe to techinfo.toyota.com so that you can download repair manual info about how to reach that ECU.

    The ECU does not need to be calibrated.

    Before you replace that ECU I recommend that you personally verify that all of the relevant fuses are sound using an ohmmeter (rather than relying on visual inspection.)
     
    #5 Patrick Wong, Aug 7, 2011
  6. Xaoh

    Xaoh New Member

    Joined:
    May 26, 2022
    18
    3
    0
    Location:
    Ottawa
    Vehicle:
    2019 Prius Prime
    Model:
    N/A
    Has anyone posted on how to remove it I? Other than just telling people to go to a mechanic …
     
    #6 Xaoh, Mar 16, 2023
  7. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    24,915
    16,216
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    #7 ChapmanF, Mar 16, 2023
  8. alftoy

    alftoy Senior Member

    Joined:
    Mar 16, 2009
    1,132
    513
    0
    Location:
    Saskatchewan, Canada
    Vehicle:
    2008 Prius
    Model:
    Base
    Take the dash apart, lots of videos for that.
     

    Attached Files:

    #8 alftoy, Mar 16, 2023
  9. Xaoh

    Xaoh New Member

    Joined:
    May 26, 2022
    18
    3
    0
    Location:
    Ottawa
    Vehicle:
    2019 Prius Prime
    Model:
    N/A
    Yup god it thanks
     
    #9 Xaoh, Mar 17, 2023
(You must log in or sign up to post here.)