1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Egr cooler hole size

Discussion in 'Gen 3 Prius Technical Discussion' started by Tiff, Dec 13, 2019.

  1. Tiff

    Tiff Junior Member

    Joined:
    Mar 8, 2018
    86
    20
    0
    Location:
    Crawley
    Vehicle:
    2010 Prius
    Model:
    III
    Hi
    Can someone pls tell me what size the holes are each side of the egr cooler.
    I need to order some rubber bungs so i can fill egr cooler with cleaner

    Thanks
     
    #1 Tiff, Dec 13, 2019
  2. hotelprisoner

    hotelprisoner Member

    Joined:
    May 31, 2007
    101
    85
    0
    Location:
    Ontario, Canada
    Vehicle:
    2010 Prius
    Model:
    Technology
    For the set I got on Amazon, I used #3 and #6 for the EGR. They also came in very handy for cleaning the Intake Manifold when I filled the thing with a mixture of Super Clean and water (Purple Power equivalent) after doing some OxiClean soaks to loosen up all the gunk. I also used a hockey puck and a C-Clamp to block the throttle body opening in the Intake with the gasket left on. The EGR and the Intake both look brand new.

    View attachment 183307
     
    #2 hotelprisoner, Dec 13, 2019
    Last edited: Dec 13, 2019
    Tiff likes this.
  3. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,671
    39,221
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    These I measured:

    EGR COOLER INFO:
    part number: 25601-37010
    Intake opening diameter (at exhaust): 20.9 mm
    exit opening diameter (at EGR valve): 25.7 mm

    I got some rubber stoppers for next time, for just the exhaust end, I think #3, per @hotelprisoner.

    Standard Stopper Sizes

    For the intake manifold I used some tapered stoppers that came with my Mighty Vac. They're designed more for plugging vacuum lines, but are long conical stoppers, kind of like stepper drill bits: very handy.

    Complete Automotive Accessory Kit MVA6000 | Mityvac
     
    #3 Mendel Leisk, Dec 13, 2019
    Tiff likes this.
  4. Tiff

    Tiff Junior Member

    Joined:
    Mar 8, 2018
    86
    20
    0
    Location:
    Crawley
    Vehicle:
    2010 Prius
    Model:
    III
    Thank you
     
    #4 Tiff, Dec 13, 2019
  5. Tiff

    Tiff Junior Member

    Joined:
    Mar 8, 2018
    86
    20
    0
    Location:
    Crawley
    Vehicle:
    2010 Prius
    Model:
    III

    Amazing thank you soo much
     
    #5 Tiff, Dec 13, 2019
  6. Tiff

    Tiff Junior Member

    Joined:
    Mar 8, 2018
    86
    20
    0
    Location:
    Crawley
    Vehicle:
    2010 Prius
    Model:
    III
    Ok heres another one then.

    Anyone know what size the holes are inside egr cooler.
    Im just going to bung ends up fill it with Mr Muscle oven cleaner for an hour, the put a metal rod type thing on my cordless drill and drill away.
    Last time i used the metal wire on a indoor clothes hanging rack but it was slightly thick, but if anyone has tried a different method do tell.

    Need to clean cooler, intake, egr.
    Replace anti roll bar bushes, balljoints and tie rods, and will also take out hybrid battery to change a few cells and clean all bus bars. Planning this just after xmas and want to get all bits in order
     
    #6 Tiff, Dec 13, 2019
  7. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,671
    39,221
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    I used a copper wire out of a cable tv coax cable, I think the reg thickness one. It takes a really skinny wire, otherwise it jams. make sure the wire end is beburred too, even that will snag. Too, I would stick to copper, and just do it by hand: you're not going to work miracles with the wire; it just helps to open passageways for the chemical incursion.
     
    #7 Mendel Leisk, Dec 13, 2019
  8. Tiff

    Tiff Junior Member

    Joined:
    Mar 8, 2018
    86
    20
    0
    Location:
    Crawley
    Vehicle:
    2010 Prius
    Model:
    III
    In the end i picked up an oven grill cooling rack for £3 from tesco had thin racks.
    Cut them of and made ends pointy. Used on a cordless drill and worked a treat.
    Finished job of by just using a jet wash to clean it. No chemicals needed. Came out spotless.
    Ive done it now at least 10 times on mine and friends cars. Also i always leave bottom (difficult bolt) off and never reinstall
     
    #8 Tiff, Sep 8, 2020
    Mendel Leisk likes this.
  9. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,671
    39,221
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    I left the bottom stud off as well (it was a bear backing it out, seemed almost seized). Might mean the cooler can be pulled out without removing the studs on the connection to exhaust manifold; time will tell.
     
    #9 Mendel Leisk, Sep 8, 2020
(You must log in or sign up to post here.)