1. Attachments are working again! Check out this thread for more details and to report any other bugs.

I have these lights on my dashboard

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by jonwilhelmjr, Mar 25, 2019.

  1. jonwilhelmjr

    jonwilhelmjr Junior Member

    Joined:
    Mar 25, 2019
    5
    1
    0
    Location:
    US
    Vehicle:
    2009 Prius
    Model:
    ----USA----
    How should I go about troubleshooting these lights? I have a Hayes book. 20190325_145547.jpeg 20190325_150402.jpeg

    SM-N950U ?
     
    #1 jonwilhelmjr, Mar 25, 2019
  2. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    110,179
    50,064
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    welcome!
    read the trouble codes with a prius aware scanner. tech stream is best, especially if you diy.

    otherwise, elm and torque are okay. service manual with code explanations and troubleshooting are at techinfo.toyota.com

    all the best!(y)
     
    #2 bisco, Mar 25, 2019
    SFO and Skibob like this.
  3. jonwilhelmjr

    jonwilhelmjr Junior Member

    Joined:
    Mar 25, 2019
    5
    1
    0
    Location:
    US
    Vehicle:
    2009 Prius
    Model:
    ----USA----
    With the scanners I have used I don't have trouble codes. I may have only used a scanner that reads engine codes

    SM-N950U ?
     
    #3 jonwilhelmjr, Mar 25, 2019
  4. Skibob

    Skibob Senior Member

    Joined:
    Sep 14, 2018
    2,912
    1,497
    0
    Location:
    Northern California
    Vehicle:
    2006 Prius
    Model:
    N/A
    Your picture is the same as 1000 others here. You need a scanner that can read ALL Toyota codes, not just the emissions codes. Get that and tell us the codes. Do not disconnect the 12v battery. You will erase some or all of the codes.
     
    #4 Skibob, Mar 25, 2019
    SFO and Raytheeagle like this.
  5. jonwilhelmjr

    jonwilhelmjr Junior Member

    Joined:
    Mar 25, 2019
    5
    1
    0
    Location:
    US
    Vehicle:
    2009 Prius
    Model:
    ----USA----
    What device will read all the codes. Or is that a dealership only device

    SM-N950U ?
     
    #5 jonwilhelmjr, Mar 25, 2019
  6. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    24,915
    16,216
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    If you do a forum search on "Mini VCI", "VxDIAG", and/or "Openport" you will have search results spilling out of your computer screen and all over your desk.
     
    #6 ChapmanF, Mar 25, 2019
    SFO, Raytheeagle and Skibob like this.
  7. jonwilhelmjr

    jonwilhelmjr Junior Member

    Joined:
    Mar 25, 2019
    5
    1
    0
    Location:
    US
    Vehicle:
    2009 Prius
    Model:
    ----USA----
    For those of you who are following this thread I have an update. I pulled the passenger rear wheel hub bearing and pulled the speed sensor cable. Found it corroded. I cleaned it and drove it to work. It sat in the 100 degree heat for 12 hours and on my way home the alarm lights went off. They stayed off for 10 miles then came on. I went to work the next morning and no lights for 10 minutes of my drive then they came back on. So......bad connection?

    SM-N950U ?
     
    #7 jonwilhelmjr, Aug 19, 2019
(You must log in or sign up to post here.)