1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Weird Windshield Washer Issue

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by joeprius2018sea, Dec 16, 2018.

  1. joeprius2018sea

    joeprius2018sea Junior Member

    Joined:
    Dec 16, 2018
    8
    3
    0
    Location:
    Seattle
    Vehicle:
    2012 Prius
    Model:
    Four
    I have a issue that I haven't seen anywhere.

    The cycle goes like this (when spraying the windshield with fluid):
    1st press - nothing
    2nd press - right side only
    3rd press - both works

    If I keep pressing, works fine. If I wait a little while, goes right back to the above cycle.

    What do you think?
     
  2. tankyuong

    tankyuong Senior Member

    Joined:
    Nov 9, 2012
    1,555
    661
    0
    Location:
    Central MO
    Vehicle:
    2012 Prius c
    Model:
    II
    Clogged nozzle
     
  3. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    110,129
    50,045
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    weak pump or switch
     
  4. joeprius2018sea

    joeprius2018sea Junior Member

    Joined:
    Dec 16, 2018
    8
    3
    0
    Location:
    Seattle
    Vehicle:
    2012 Prius
    Model:
    Four
    Checked the nozzle, doesn't seem to be clogged. Does the 1 pump drive the front and back washers?

    Maybe I'll check the 3-way check valve under the hood.
     
  5. NutzAboutBolts

    NutzAboutBolts Senior Member

    Joined:
    Mar 5, 2013
    1,476
    1,552
    0
    Location:
    Bay Area
    Vehicle:
    2012 Prius
    Model:
    Four
    Maybe you need to press on the lever harder?
     
  6. tweedle99

    tweedle99 Member

    Joined:
    Feb 7, 2012
    103
    60
    0
    Location:
    Round Rock, TX
    Vehicle:
    2010 Prius
    Model:
    III
    It's the check valve, part no 85321-28020. It's under the hood liner.

    My original symptom was weak passenger side spray. Cleaned the nozzle still the same until i read some old post.

    Bought aftermarket one from ebay, https://tinyurl.com/yda5tu73
     
    joeprius2018sea and Raytheeagle like this.
  7. sam spade 2

    sam spade 2 Senior Member

    Joined:
    Mar 31, 2018
    7,035
    2,790
    0
    Location:
    USA
    Vehicle:
    2017 Prius c
    Model:
    Four
    It can also be a leak in the plumbing.

    In order to get almost instant liquid delivery, the hoses all must stay full, or almost full, all the time.
    If that is the case, it might be spraying out where the leak is when the pump runs.

    I do NOT think the front pump has anything to do with the back washer.
    But that's just a guess.
     
  8. joeprius2018sea

    joeprius2018sea Junior Member

    Joined:
    Dec 16, 2018
    8
    3
    0
    Location:
    Seattle
    Vehicle:
    2012 Prius
    Model:
    Four
    thanks for the tip. I don't see any leaks. Going to order a check valve, it's pretty cheap.
    are there any clamps that hold the hose onto it?
     
  9. tweedle99

    tweedle99 Member

    Joined:
    Feb 7, 2012
    103
    60
    0
    Location:
    Round Rock, TX
    Vehicle:
    2010 Prius
    Model:
    III
    No clamps, just held on by just friction. Just make sure that the new one is connected the same.
     
    joeprius2018sea likes this.
  10. grantb3

    grantb3 Junior Member

    Joined:
    Nov 6, 2009
    60
    20
    0
    Location:
    Orange County, CA
    Vehicle:
    2010 Prius
    Model:
    III
    Also having a problem with the passenger side (only) windshield wiper fluid spray. What's the trick to getting these bad boys off? It's besting me!
     

    Attached Files:

    Mendel Leisk likes this.
  11. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,664
    39,220
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    2nd that. And without destroying the liner or the fastener, if possible.
     
  12. wheezyglider

    wheezyglider Active Member

    Joined:
    Mar 12, 2011
    247
    178
    0
    Location:
    SF Bay Area
    Vehicle:
    2010 Prius
    Model:
    Five
    I pulled the hood liner fasteners on my 2010 to replace the check valve a few months ago. Which fixed my weak-on-one-side spray problem. I used a standard clip removal tool (one of those forked flat blade thingies), and yes I made small tear in the liner and a couple of the clips were damaged. The liner also crushes easily.

    If I were doing it again I'd say buy some replacement clips in advance so that you can trade being more abusive to the old clips against being extra careful with the expensive and delicate liner. Then: pry the clips up gently until you can grab with a pliers and rip them out without further touching the liner.

    So far I haven't needed to replace the damaged clilps. But I did notice Toyota replaced them with a better design. Good luck!
     
    Mendel Leisk likes this.
  13. tweedle99

    tweedle99 Member

    Joined:
    Feb 7, 2012
    103
    60
    0
    Location:
    Round Rock, TX
    Vehicle:
    2010 Prius
    Model:
    III
    Do you have the parts no?
     
  14. wheezyglider

    wheezyglider Active Member

    Joined:
    Mar 12, 2011
    247
    178
    0
    Location:
    SF Bay Area
    Vehicle:
    2010 Prius
    Model:
    Five
    For the clips? From my notes:
    90467A0003 MSRP $1.84
    The hood insulator uses 6 of them. That would only be $8 from TPD, but another $9 in shipping. A bag of knock-off ones on Amazon can be had for about $8 with free shipping (but not Amazon fulfillment). Original toyota ones on ebay are surprisingly expensive (like $5).​
     
    tweedle99 likes this.
  15. grantb3

    grantb3 Junior Member

    Joined:
    Nov 6, 2009
    60
    20
    0
    Location:
    Orange County, CA
    Vehicle:
    2010 Prius
    Model:
    III
    Yeah I don't know that I would use those same clips again. I partially destroyed one corner of the liner and the clip isn't out yet.