1. Attachments are working again! Check out this thread for more details and to report any other bugs.

JBL to Aftermarket

Discussion in 'Gen 2 Prius Audio and Electronics' started by Chad81, Aug 10, 2015.

  1. Chad81

    Chad81 New Member

    Joined:
    Aug 10, 2015
    3
    0
    0
    Location:
    Charlotte, NC
    Vehicle:
    2005 Prius
    Model:
    II
    Good Morning to everyone, I have been reading the forums for the past few weeks and recently purchased a used 2005 Prius with the JBL 9 speaker sound system. I was looking for a few feature this unit did not have (mainly bluetooth audio) and wanted a touchscreen so I purchased an AVH-270BT for the car. I am a bit fuzzy on a few things and maybe just haven't found the right information.

    I have been reading about the upgrade and I am trying to understand the setup (without having pulled the dash apart yet) so that when I get in there I am fully prepared. I have installed your typical radio with 4 speakers several times before and you simply match the wiring harness of the radio with the wiring adapter harness for the vehicle, plug it in and your good to go. This does not sound like that at all.

    If I understand correctly all 9 speakers are wired to a JBL amp under the passenger seat. So instead of wiring up each speaker I simply plug up the Metra TYTO adapter to the preamp out on the stereo to the input harness for the JBL amp?

    Even if I have that much right (and I am certainly not sure) it sounds like I need another resister for something else. I just want to make sure I am not going to throw codes or anything once I am done. Steering wheel controls are not at all important.

    Lastly, I wanted to know if it makes sense to keep the current amp or save the $55 for the Metra harness and swap for a better amplifier.

    I appreciate your help and feedback in advance.
     
  2. 69shovlhed

    69shovlhed Surly tree hugger

    Joined:
    May 13, 2012
    2,170
    750
    0
    Location:
    Delaware
    Vehicle:
    2017 Prius Prime
    Model:
    Prime Premium
    the jbl amp incorporates some of the functions that would be in a normal head unit. so if you wanted to change the amp you'd have to rewire the whole mess. I would checkout crutchfield.com to see what all you need to replace just the head unit. they can probably sell you exactly what you'll need and will include instructions with it. and they got a help line if you do have any problems getting it to work.
     
  3. Chad81

    Chad81 New Member

    Joined:
    Aug 10, 2015
    3
    0
    0
    Location:
    Charlotte, NC
    Vehicle:
    2005 Prius
    Model:
    II
    69shovlhed Thanks for your response! I have the following in my Amazon cart:

    Metra 70-1761
    Metra TYTO-01
    Scosche Dash kit for Prius

    And I have a 68ohm .5 watt resistor for the A/C functions.

    Does all this sound right?
     
  4. 69shovlhed

    69shovlhed Surly tree hugger

    Joined:
    May 13, 2012
    2,170
    750
    0
    Location:
    Delaware
    Vehicle:
    2017 Prius Prime
    Model:
    Prime Premium
    I'm not sure. I haven't put an aftermarket head unit in my '06 w/ JBL yet because no one makes an adapter to use the factory blue tooth mic. the base model needed a harness adapter which had the 68 ohm resister built into it. I used a metra axxess unit for the steering wheel buttons, and that was all I needed. the adapter harness was also by scosche; you need it so you won't have to ruin your factory harness.
    the reasons I like crutchfield are: fast shipping, advisors that can tell you exactly what you need for your car, and they send detailed instructions for the install. I've never needed the help line, but its there if you need it.
     
  5. cballdog811

    cballdog811 New Member

    Joined:
    Sep 1, 2015
    1
    0
    0
    Location:
    la
    Vehicle:
    2005 Prius
    Model:
    Plug-in Base
    And transferring to aftermarket head unit please post links here thank you very much