1. Attachments are working again! Check out this thread for more details and to report any other bugs.

LT fender liner retainers/clips

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by skiddl3s, Dec 20, 2014.

  1. skiddl3s

    skiddl3s New Member

    Joined:
    Dec 20, 2014
    2
    0
    0
    Vehicle:
    2011 Prius
    Model:
    Two
    I'm looking to replace my front driver fender liner.

    Are there universal retainers or clips I may use for this DIY project?

    Another post noted that 11 of the 90467-07164 is required for each fender liner in front.

    Fender Splash Shield Push-Type Retainer
    Black Nylon
    Head Diameter: 20mm
    Stem Length: 10mm
    Fits Into 7mm Hole

    Will this fastener work similarly for a 2011 Toyota Prius front fender liner LT?

    The attached diagram indicates there are 10 different fasteners/screws/clips/what-have-you's to replace the fender liner. It's a tad bit pricey to get each one... as you can imagine.

    Any advice would be appreciated. Thanks!
     

    Attached Files:

    #1 skiddl3s, Dec 20, 2014
  2. Yakoma

    Yakoma Active Member

    Joined:
    Oct 17, 2014
    470
    124
    0
    Location:
    ATL-ish
    Vehicle:
    2008 Prius
    Model:
    N/A
    I feel your pain. I ended up getting an assortment of sizes as I have missing fasteners all over my used 2008. Ebay sells a boxed assortment for about $24. Had to get some of the clips/screws from the Dealer as I couldn't locate them online. Good luck.
     
    #2 Yakoma, Dec 20, 2014
  3. skiddl3s

    skiddl3s New Member

    Joined:
    Dec 20, 2014
    2
    0
    0
    Vehicle:
    2011 Prius
    Model:
    Two
    I called the dealership and he quoted me $27 total per the diagram above.
    Body shop lists two that's only required: 9015960488 and 9046710183. However, the first one is a metal screw, which doesn't make sense. There must be a similar plastic fastener that fits the bill.

    90159-60488 (21838):
    M6.3-2.5 x 24 mm
    16mm washer
    10 mm hex

    90467-10183 (20869):
    Front Fender Liner Push-Type Retainer
    Head diameter:18mm
    Stem Length: 7.5mm
    Fits into 7mm hole

    What would 21838 look like as a push-type retainer?
     
    #3 skiddl3s, Dec 20, 2014
  4. Yakoma

    Yakoma Active Member

    Joined:
    Oct 17, 2014
    470
    124
    0
    Location:
    ATL-ish
    Vehicle:
    2008 Prius
    Model:
    N/A
    Yes, the first one is a screw going into plastic/nylon clip. The clip goes into the fender hole - and the screw attaches the fender liner to the clip/fender. If you're saying $27 is for all the pieces in Diagram 53875A or B, that's not a bad price for all that stuff if you ask me. You could go to a hardware store and they could maybe assemble a bunch of pieces that cost only $10, but they won't necessarily look very right nor will they necessarily stay in place over the long haul. Know anybody at a non-dealer body shop? They may be able to help you for less than Toyota.
     
    #4 Yakoma, Dec 20, 2014
  5. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,708
    39,248
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    There are some metal screw fasteners, as you can readily see by having a look around the car. They're not that impervious to rust either. ;(
     
    #5 Mendel Leisk, Dec 21, 2014
(You must log in or sign up to post here.)