What does the water pump mount to? Can it leak?

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by dmaxdmax, Sep 15, 2012.

  1. dmaxdmax

    dmaxdmax Junior Member

    Joined:
    Dec 18, 2006
    43
    10
    0
    My water pump is leaking from a gasket. My mechanic replaced it a few months ago and is fixing it with charge (as well he should). He says it mounts to a place that also appears to be seeping coolant and may need to be removed and sealed.

    What the heck is he talking about?
     
    #1 dmaxdmax, Sep 15, 2012
  2. Britprius

    Britprius Senior Member

    Joined:
    Jun 14, 2010
    5,194
    1,917
    0
    Location:
    Herefordshire England
    Vehicle:
    2008 Prius
    The engine water pump is of the same construction as any other petrol engine pump. There is basically just one card type gasket between the engine and the pump, if this is leaking the pump needs to be removed. The mating surfaces on the pump and engine cleaned and a new gasket fitted on reassembly. New Toyota SLLC coolant should be used and the system bled to remove all trapped air.
     
    #2 Britprius, Sep 15, 2012
  3. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    111,177
    50,607
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    'fixing it with charge' means he's charging you to fix something that he apparently did incorrectly?
     
    #3 bisco, Sep 15, 2012
  4. dmaxdmax

    dmaxdmax Junior Member

    Joined:
    Dec 18, 2006
    43
    10
    0
    typ0 - s/b "no charge"
     
    #4 dmaxdmax, Sep 15, 2012
  5. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,200
    6,489
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    I recently purchased the correct Toyota replacement engine coolant pump which comes with the gasket. The gasket appears to be made of sheet metal covered in a black rubber coating. The service manual does not indicate any need for sealant.

    The pump impeller sticks out the rear of the pump housing. As it spins, it pumps engine coolant through the cavity (located in the front of the engine block) which surrounds the impeller. Hence if the gasket is not sealing then coolant will leak out.

    Did your mechanic use the correct Toyota pump and gasket; or aftermarket? If aftermarket then perhaps sealant is required if the pump's machined face is not sufficiently flat or if the gasket is a type that requires sealant.
     
    #5 Patrick Wong, Sep 15, 2012
  6. Avi's Advanced Automotive

    Avi's Advanced Automotive Independent hybrid repair shop

    Joined:
    Jun 28, 2012
    776
    362
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2005 Prius
    Model:
    Three
    I see most aftermarket water pumps coming with paper gaskets while Toyota designed it with a coated metal gasket.
    In my shop I have a list of aftermarket parts that are not allowed in the shop. For instance I will not use the brand GMB ever. I'll bet he installed something along those lines and now the paper gasket is leaking. I have replaced several of these water pumps and have never had a problem. I use AISIN brand pumps as they are the same ones as the dealer sells.

    You might kindly ask him to install an AISIN pump if he did not do so in the first place. At the very least see if the replacement gasket can be purchased from Toyota or an identical one.

    As far as what it is mounted to, he is talking about the timing cover. I have never seen one leak, however, it could be possible.

    Avi
     
    #6 Avi's Advanced Automotive, Sep 15, 2012
(You must log in or sign up to post here.)