1. Attachments are working again! Check out this thread for more details and to report any other bugs.

tanabe df210 rear too low!

Discussion in 'Gen 3 Prius Accessories and Modifications' started by crazyjeys, Jul 29, 2012.

  1. crazyjeys

    crazyjeys Member

    Joined:
    Apr 9, 2012
    135
    16
    0
    Location:
    Sunny Socal
    Vehicle:
    2012 Prius
    Model:
    Three
    Just installed my tanabe df210's. The rears are too low for my liking. Was thinking that the setup would be leveled but it seems like that the car is nose high. It there such a thing like a spacer that i can put to jack up the rear 1/4 of an inch?
     
    #1 crazyjeys, Jul 29, 2012
  2. Jay J

    Jay J Active Member

    Joined:
    Apr 24, 2007
    469
    253
    1
    Location:
    Torrance, CA
    Vehicle:
    2012 Prius
    Model:
    Two
    You might be able to adapt a mercedes spacer for the rear, but I don't recommend it.
     
    #2 Jay J, Jul 29, 2012
  3. peterjmc

    peterjmc Ping pong in Ding Dang...

    Joined:
    Dec 5, 2010
    917
    189
    0
    Location:
    Clarksburg, MD
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Advanced
    Eibach and H&R springs don't give you the saggy butt look. you could get shims. But the way the springs are seated... It might not be a good idea.
     
    #3 peterjmc, Jul 29, 2012
  4. Russ D

    Russ D Junior Member

    Joined:
    May 6, 2012
    22
    1
    0
    Location:
    So Cal
    Vehicle:
    2010 Prius
    Model:
    II
    What wheels are you running on the car right now? Maybe it's just your eyes messing with you? Check out this car with the same springs: tanabe df210+enkei rpf1 teaser | PriusChat if anything it almost looks like the nose of that car is a little down. Post up some pics! Maybe you're ok
     
    #4 Russ D, Jul 29, 2012
  5. Dark_matter_doesn't

    Dark_matter_doesn't Prius Tinkerer

    Joined:
    Aug 8, 2009
    691
    151
    41
    Location:
    Seattle, WA
    Vehicle:
    2010 Prius
    Model:
    IV
    When I put the back NF-210's on my car and put it on the ground, I was a bit shocked how low the back end looked. But after putting on the fronts, the back didn't look weirdly low.

    Drive it around and look at the car in other locations. The extra low appearance might be due to where you're currently parked. My driveway & carport can make my car seem tipped to one side.
     
    #5 Dark_matter_doesn't, Jul 30, 2012
  6. HI MPG

    HI MPG Active Member

    Joined:
    Aug 25, 2009
    789
    133
    93
    Location:
    Orange County, CA
    Vehicle:
    2010 Prius
    Model:
    IV
    I have the NF210's, and I have to agree with the OP. However, I also agree with Dark that it's a matter of perspective. Some of the other aftermarket manufacturers provide a "raked" look. Tanabe tries to achieve a more "level" approach and with the exterior shape of the Prius being basically a wedge, this gives the impression of a saggy rear end.
     
    #6 HI MPG, Jul 30, 2012
  7. crazyjeys

    crazyjeys Member

    Joined:
    Apr 9, 2012
    135
    16
    0
    Location:
    Sunny Socal
    Vehicle:
    2012 Prius
    Model:
    Three
    right now i'm still running on the stock wheels. i'll go and post up pics later and help me decide if it is or it is not...
     
    #7 crazyjeys, Jul 30, 2012
  8. crazyjeys

    crazyjeys Member

    Joined:
    Apr 9, 2012
    135
    16
    0
    Location:
    Sunny Socal
    Vehicle:
    2012 Prius
    Model:
    Three
    here's a couple of not so good shots that i took yesterday.. you be the judge.. is the rear sitting too low or is it just leveled?


    [​IMG]
    IMAG0837 by crazyjeys, on Flickr

    [​IMG]
    IMAG0839 by crazyjeys, on Flickr
     
    #8 crazyjeys, Jul 31, 2012
  9. Tremiata

    Tremiata Junior Member

    Joined:
    Jul 24, 2012
    2
    0
    0
    Vehicle:
    2012 Prius
    Model:
    II
    Can you measure from center of hub to center of fender lip front/rear and see if there is a difference and compare to a stock measurement?
     
    #9 Tremiata, Jul 31, 2012
  10. HI MPG

    HI MPG Active Member

    Joined:
    Aug 25, 2009
    789
    133
    93
    Location:
    Orange County, CA
    Vehicle:
    2010 Prius
    Model:
    IV
    You can compare with mine:

    [​IMG]

    [​IMG]
     
    #10 HI MPG, Jul 31, 2012
    1ULV2H8 likes this.
  11. crazyjeys

    crazyjeys Member

    Joined:
    Apr 9, 2012
    135
    16
    0
    Location:
    Sunny Socal
    Vehicle:
    2012 Prius
    Model:
    Three
    i'll measure it when i get home tonight...
     
    #11 crazyjeys, Jul 31, 2012
  12. crazyjeys

    crazyjeys Member

    Joined:
    Apr 9, 2012
    135
    16
    0
    Location:
    Sunny Socal
    Vehicle:
    2012 Prius
    Model:
    Three
    that's the stance that i want!!! i think your rear's are a little bit higher than mine... i don't know why though, i didn't do any mods and there's nothing in the trunk too!

    btw, nice car!
     
    #12 crazyjeys, Jul 31, 2012
  13. HI MPG

    HI MPG Active Member

    Joined:
    Aug 25, 2009
    789
    133
    93
    Location:
    Orange County, CA
    Vehicle:
    2010 Prius
    Model:
    IV
    Thanks.
    Mine is a bit higher, but the difference is a result of the different type of springs. I'm running the NF210s, and you're running the DF210s. According to the Tanabe website, the NF drops the rear by 1.1 inches whereas the DF drops it by 1.6. My ride is probably a little spongier than yours though.
     
    #13 HI MPG, Jul 31, 2012
  14. eseymour72

    eseymour72 Junior Member

    Joined:
    Feb 26, 2012
    46
    6
    0
    Location:
    Lincoln City, OR
    Vehicle:
    2017 Prius Prime
    Model:
    Prime Advanced
    I just installed the Eibachs on mine and it's a 1.1" front/ 0.8" drop in rear (progressive rate springs).

    I like the NF210 but the DF210 is too low in the rear in my opninon.
     
    #14 eseymour72, Aug 18, 2012
(You must log in or sign up to post here.)