How to program features - scan guage?

Other than the few items that owner instructions are provided for, I haven't heard of anybody that's found a way of changing the other customization items listed in the owner's manual. On the TIS site, it says the dealer needs to connect the car to some proprietary Toyota system to make the changes.

 

I would like to learn how to do this as well.

Toyota uses the same tool to change items. It’s a laptop running Win XP with a USB based OBDCII connector. They do use custom software but the end result is codes sent over OBDCII.

If someone had a bus analyzer they could capture all the coded and results.

 

I just installed my scan guage II and I really like it. I could not find any way to change the programming but you can check for codes and reset them, if needed. The thing I like, is the way I can moitor 4 things at once. I am watching RPM, water temperature, battery voltage (12v battery) and miles per gallon. The miles per gallon follow the sliding guage next to the speedometer very closely, BUT it reads up to 9999mpg. I was sometimes running down the road at over 1000mpg. The rpm is interesting because you can see when the engine is on or off. It also varies all over the place. When I am accelerting and it sounds like the engine is racing it is really around 3500rpm. It sounds like the squirrels are being over worked, but it's not as bad as it sounds. The voltage is 13.5-14.5 volts. Pretty boring information unless something is wrong. Water temperature is very cool because you will notice water temp values change dramatically. The auto climate control kicks the heat on right at 105 degrees. If I am sitting at a light and the engine is off, the water temp drops as low as 175 degrees. The normal range for highway is 188-198 degrees. It would appear there is a 195 degree thermostat in the engine, after watching this guage.. The one thing that surprised me is the MPH guage. My portable GPS says at 70mph my car indicates it is going 72mph. The scan guage says 70mph. The scan guage reads the computer and gives an accurate speed. Somewhere between the computer and the speedometer there is a 1.5-2mph increase which really stinks. I find myself setting the cruise at 72 because I know it is 2mph off. The other cool thing is there are 63 possible back light color variations. I was able to adjust the color to match the other guages. I ran the cable behind the dash and through the space between the dash and the steering column. I mounted the unit on the dash so I can see it throught the top part of the steering wheel. You only see a small portion of the cable and it is right in front of you. I cover it with a small black wash cloth so no one can tell it's there. I used the velcro that came with the kit. It was $159 and worth every penny to me. The trip features are really neat too. You can calibrate the scan guage II trip functions seperate from everything else. There is no installation, just plug it in, set it up and you are done.

 

No, I have the scan guage II and I could not see any way to make those kind of changes but the things you can monitor are really cool. Mine is on everytime I drive down the road.

 

One person has done it themselves... me. I've changed customizable settings, registered TPMS sensors and added a key. You need a copy of the Techstream software and a J2534 compatible interface cable that comes with Techstream compatible drivers.

http://priuschat.com/forums/gen-iii...odifications/65998-programming-ourselves.html

 

Very informative, can you possible take picture ? I am considering the ScanGauge II

 

Just be aware that the "Xgauges" developed for the gen2 Prius
[see the several threads over on CleanMPG] won't work on the
gen3 and that research into an updated set basically hasn't even
begun yet. It's going to take a whole wad of reverse-engineering
and likely some updates to the Scangauge firmware itself.
.
_H*

 

I haven't tried to program my own functions through the Xguage feature because the ones that showed up, when I hooked it up, were the ones I was interested in. I monitor RPM, MPG, Water Temperature, and Voltage. It works great. A fun fact I noticed is, the engine stays runnig around 1000rpm until you slow down around 40mph or less. I have been cruising along at 35 mph and thought the engine was on until I looked at the scan guage. I ran a couple of miles at that speed with the engine off.

 

rachaelseven is in a world of her own...her and her shady software hookups...(ok, I'm just jealous, sue me)

 

Found techstream Now I just need to order the cable and I can play...ahh...good times are ahead...

 

What cable did you get and where did you get it from?

Thanks!

 

Mongoose MFC, made by Drew Technologies. I ordered it direct from them, but I'm told it can be found for less on eBay.