Too much transmission fluid consequences?

Wouldn't worry about it, mine is the same.

 

If it was an automatic transmission, you could have trouble. Since it's not, you would have to have it grossly overfull before you had an issue, eg seal leaks

 

Mine took a full 4 quarts and then was driven for 20,000 miles, half highway. No problems, no leaks, no MPG loss.

Wayne

 

4 US quarts is the capacity spec, and that is the amount that I fill.

 

If you want to allay your fears, just remove the fill plug when you can find level ground to park on. Any excess will drain out.

 

I put little more than 3.5 quarts. Did I putting too little? I remember when I drained the old fuild, it was about 4 quarts. so I need to add more?

 

Just to clarify, we are talking about transaxle fluid, not engine oil...

When replacing transaxle fluid, you are supposed to have the vehicle level and add enough until the new fluid starts to seep out of the fill hole.

The spec is 4 US quarts fill capacity. I have found that this spec is accurate. If your transaxle fluid is 0.5 quart low, I think it would be a good idea to add more fluid soon.

It's not clear at what point insufficient fluid will result in damage. Considering that the cost of transaxle replacement is well into four digits, I don't see the point of taking unnecessary risks with that component.

 

For the CVT case, you want it up to the fill plug line. For the engine, 3.5 quarts of motor oil is plenty

 

yes, I am talking about transaxle fluid. Anyway, it was little under what the spec said. and it was changed last summer by myself and the car was on a level surface. and the drain hole drained some extra. that is how I know it was only little more than 3.5 quarts. maybe about 3.7 quarts. I will add the missing fluid in few days.

 

All of you confuse me now. from this site, Spring maintenance
it stated clearly that "So 3.3 to 3.5 quarts seems about right for drain-n-refill, where the dry spec is a little over 4."
If all you guy are drain-n-refill, how can you guys fill up with 4 quarts?? I do not understand.

 

Hobbit's experience differs from ours. When you do the change, you can see for yourself how much fluid is needed so that the fluid level reaches the bottom of the fill hole.

 

why is Hobbit's experience differs from ours?? same car (second gen Prius). same CVT. so the capacity for holdong the fuild should be the same. The only thing that can be different is when you drain the fuild, you can completely drain out all the fuild, whereas, when I drain the fuild, there are still some portion of the fuild inside. I am not sure this will be the case.

 

The following is from Hobbit's website cited in your post #12 above:

"One quart in, check underneath for leaks. Two more quarts in,
and finally open up the level-check plug. Spec is 0 - 5 mm below the level
of that hole; a little finger inserted and dipped *way* down could just barely
find some fluid after three quarts. About a third of a quart later, it was
almost to the lip, so I reinstalled the level plug and and added a splash or
two more. So 3.3 to 3.5 quarts seems about right for drain-n-refill, where
the dry spec is a little over 4."

Note that Hobbit did not fill to the point where the fluid level was at the bottom of the fill hole. Rather the level was near the bottom.

Perhaps he did not drain the old fluid to the same extent as other posters did. Perhaps there's production variability with the transaxles. In any event, as long as you have 4 US quarts of new fluid available and fill until you start to see new fluid coming out of the fill hole (or use up the 4 quarts), you'll be in good shape.

 

The car may not have been perfectly level. May have been colder or warmer than when I used to change my fluid. Car itself may have been cold or hot, I did mine room temp

Here in Canada, you can buy WS in a 4 litre tin can. I had made a ramp out of old railway ties at the hobby farm, and the ramp was perfectly level on top.

With the Prius on top of the ramp, fluid drained, I'd refill by using a small pump until fluid started to ooze out the fill plug. I usually had about 150 ml left in the can

 

I was told the CVT transaxle was a sealed system. No transmission fluid to ever change....

 

welcome! That is the standard statement at the service department. However, most on this forum have discovered that the fluid is very dirty at 12K-35K and needs changed. There after it may not be as important and only time will tell.

 

Also I was shopping at wal-mart today and read the back of the dextron 6 bottle and it said for WS and IV service. This stuff was less than half the price of the WS at the dealer that was not synthetic as far as I can tell.