1. Attachments are working again! Check out this thread for more details and to report any other bugs.

2013 evap purge valve - how to remove?

Discussion in 'Gen 3 Prius Technical Discussion' started by Thiccaca, Feb 10, 2024.

  1. Thiccaca

    Thiccaca New Member

    Joined:
    Feb 10, 2024
    2
    0
    0
    Location:
    Ithaca, NY
    Vehicle:
    2013 Prius
    Model:
    One
    The evap purge valve on my 13 needed replacing. Easy enough fix. Went well, and I even have the new valve in and it is working fine.

    But....

    I can't figure out how to remove the OLD valve. The bracket that holds it to the engine can't be seen at all, and the screw that holds the bracket to the valve itself is at such an angle I can get purchase with a Phillips head. Just not enough room even with a stubby one. Afraid I might strip the head.

    How does this thing come off?
     
    #1 Thiccaca, Feb 10, 2024
  2. Tombukt2

    Tombukt2 Senior Member

    Joined:
    Nov 29, 2020
    10,373
    1,792
    0
    Location:
    Durham NC
    Vehicle:
    2009 Prius
    Model:
    Base
    Don't you have to undo the whole bracket that's holding the hold evap canister and all that so it drops down so you can get to the screw and all that I know on my van which is an '01 or two similar problem All of these purge valves have a similar issue trying to get them off of the canister bracketry. Some of them rust and they fall apart while you're trying to get them off I have not personally taken off the setup on the generation 3 but on the two it looks like the canister and bracket may need to be lowered to change the purge valve and it's related receptacle or plug however you look at it
     
    #2 Tombukt2, Feb 11, 2024
  3. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,671
    39,221
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    Think you’re talking about this:

    IMG_3417.jpeg

    If so, there’s a largish bolt that holds it to the intake manifold, nothing fancy.
     
    #3 Mendel Leisk, Feb 12, 2024
    Last edited: Feb 12, 2024
  4. Thiccaca

    Thiccaca New Member

    Joined:
    Feb 10, 2024
    2
    0
    0
    Location:
    Ithaca, NY
    Vehicle:
    2013 Prius
    Model:
    One
    That is exactly what I mean. Do I need to remove the intake manifold to remove?
     
    #4 Thiccaca, Feb 17, 2024
  5. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,671
    39,221
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    No. It’s awkward to reach though. It has one bolt, maybe 12 mm socket size.
     
    #5 Mendel Leisk, Feb 18, 2024
  6. Tombukt2

    Tombukt2 Senior Member

    Joined:
    Nov 29, 2020
    10,373
    1,792
    0
    Location:
    Durham NC
    Vehicle:
    2009 Prius
    Model:
    Base
    No is your picture shows It's almost removed there's a bolt and a slip and you're holding it.
     
    #6 Tombukt2, Feb 18, 2024
(You must log in or sign up to post here.)