1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Fumoto oil drain valve

Discussion in 'Gen 3 Prius Accessories and Modifications' started by abubin, Feb 8, 2023.

  1. abubin

    abubin Member

    Joined:
    Dec 7, 2019
    182
    91
    0
    Location:
    Malaysia
    Vehicle:
    2012 Prius
    Model:
    N/A
    Anyone using Fumoto oil drain valve? I am thinking of putting it on my Prius Gen 3 on the next oil change.

    F106-LC-10.jpg


    Read that there might be clearance issue. Especially when the car is already very low, might have risk of getting the plug hit going over humps.
     
    #1 abubin, Feb 8, 2023
    Foxglove likes this.
  2. Ryan Will

    Ryan Will Member

    Joined:
    Jun 18, 2022
    68
    43
    0
    Location:
    Southern California
    Vehicle:
    2015 Prius
    Model:
    Three
    I had one of these on my previous car (a Ford Focus), and it definitely made oil changes less messy. The downside was that it took a lot longer to drain, but the trade-off of less mess was much more of a plus for me. I obviously cannot speak on clearance issues since I do not have one on my Prius, but have definitely thought about getting one, as well.
     
    #2 Ryan Will, Feb 8, 2023
    Foxglove likes this.
  3. StarCaller

    StarCaller Senior Member

    Joined:
    Feb 15, 2014
    1,255
    706
    0
    Location:
    Cedar Crest, NM, USA
    Vehicle:
    2014 Prius
    Model:
    Two
    Works perfect for me since almost 9 years /
     
    #3 StarCaller, Feb 8, 2023
    Foxglove likes this.
  4. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,671
    39,221
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    I’d be a little nervous about the clearance.
     
    #4 Mendel Leisk, Feb 8, 2023
  5. xliderider

    xliderider Senior Member

    Joined:
    Apr 19, 2012
    7,919
    3,142
    0
    Location:
    Honolulu, HI
    Vehicle:
    2011 Prius
    Model:
    Three
    My concern was that it allowed some volume of old oil to remain in the oil pan.

    I removed the valve at the end of the drain operation to allow the remaining oil to drain out. Still a lot less mess than removing a traditional drain bolt with a full oil pan.

    Posted via the PriusChat mobile app.
     
    #5 xliderider, Feb 8, 2023
  6. abubin

    abubin Member

    Joined:
    Dec 7, 2019
    182
    91
    0
    Location:
    Malaysia
    Vehicle:
    2012 Prius
    Model:
    N/A
    You are using this on your gen 3? How's the clearance?
     
    #6 abubin, Feb 10, 2023
  7. abubin

    abubin Member

    Joined:
    Dec 7, 2019
    182
    91
    0
    Location:
    Malaysia
    Vehicle:
    2012 Prius
    Model:
    N/A
    Have you tried pouring new oil into the engine to displace the old oil stuck at the bottom of the oil pan? This would somewhat drain a bit more of the dirty oil without removing the plug.
     
    #7 abubin, Feb 10, 2023
  8. ASRDogman

    ASRDogman Senior Member

    Joined:
    May 29, 2018
    6,421
    3,410
    0
    Location:
    Florida
    Vehicle:
    2010 Prius
    Model:
    Two
    If you only raise the right front wheel, you'll get more oil out.
    And you will NEVER get ALL the oil out... Leaving 3 or 4 ounces in is NOTHING....
     
    #8 ASRDogman, Feb 10, 2023
    Foxglove likes this.
  9. xliderider

    xliderider Senior Member

    Joined:
    Apr 19, 2012
    7,919
    3,142
    0
    Location:
    Honolulu, HI
    Vehicle:
    2011 Prius
    Model:
    Three
    Clearance is decreased, as expected.

    Posted via the PriusChat mobile app.
     
    #9 xliderider, Feb 10, 2023
  10. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,671
    39,221
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    With oil changes. I’ve noticed since raising the front a few inches more*, then putting in the usual specd quantity, oil level on the dipstick is nearly 1/4” below top mark. Which is ok with me, since so far it never budges from there.

    Conclusion: I’m draining a bit more with the increased tilt.

    My 2 cents on the valve: I’ve never had a problem just with the drain bolt, so…

    * Using same jack, but run front wheels up on low-rise ramps, and added some shim to the jack cradle.
     
    #10 Mendel Leisk, Feb 10, 2023
  11. abubin

    abubin Member

    Joined:
    Dec 7, 2019
    182
    91
    0
    Location:
    Malaysia
    Vehicle:
    2012 Prius
    Model:
    N/A
    Just changed my oil on my Gen 3. Tried the fumoto drain valve on it. It does add a bit to the clearance. So I didn't installed it. I will use it on my Prius C as that car have a higher clearance.
     
    #11 abubin, Feb 12, 2023
    Last edited: Feb 12, 2023
(You must log in or sign up to post here.)