1. Attachments are working again! Check out this thread for more details and to report any other bugs.

vent cover removal

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by volcano, Feb 7, 2022.

  1. volcano

    volcano Junior Member

    Joined:
    Jun 28, 2013
    7
    0
    0
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    ok i have an 2008 prius, the vent cover to the right of the steering wheel covering the drive shifter is cracked and want to buy a replacement part on ebay and replace it. problem is i dont know how to remove it. on the vent to the left of the steering wheel it looks like you can pry it off but the one to the right of the steering wheel the new part doesn't look like you can just pull it off. does anyone know how to do this?
     
    #1 volcano, Feb 7, 2022
  2. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,525
    8,428
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    Youtube
     
    #2 JC91006, Feb 7, 2022
  3. TMR-JWAP

    TMR-JWAP Senior Member

    Joined:
    Aug 12, 2016
    6,404
    6,062
    0
    Location:
    Columbia, SC
    Vehicle:
    2007 Prius
    Model:
    Touring
    Remove the left vent.
    Remove the upper and lower steering cover trim pieces..
    Remove the center left vent. (most likely in several pieces)

    As mentioned, there are many videos. Look for Gen 2 prius MFD replacement videos. There's one out there that shows how to replace an MFD in about 10 minutes. It does a good job showing how to remove the vents and trim pieces.
     
    #3 TMR-JWAP, Feb 8, 2022
    ydpplqbd likes this.
  4. volcano

    volcano Junior Member

    Joined:
    Jun 28, 2013
    7
    0
    0
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    thank you I found a video. I was looking at videos for vent removal and did not find one that removed just the power button vent. I dont need to remove MFD screen though.
     
    #4 volcano, Feb 8, 2022
  5. Another

    Another Senior Member

    Joined:
    Jun 22, 2021
    1,802
    512
    0
    Location:
    Naples, Florida
    Vehicle:
    2007 Prius
    Model:
    Touring
    Might help everyone if you posted link to video
     
    #5 Another, Feb 8, 2022
  6. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    24,906
    16,213
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    Because of the way pieces overlap, you have to start with the one on the left. Then you just work your way across.
     
    #6 ChapmanF, Feb 8, 2022
    ydpplqbd likes this.
  7. alftoy

    alftoy Senior Member

    Joined:
    Mar 16, 2009
    1,132
    513
    0
    Location:
    Saskatchewan, Canada
    Vehicle:
    2008 Prius
    Model:
    Base
    To access Prius dash center stack (MFD, speedo, radio etc) requires removal of vents and power button panel as in this video to remove speedo cluster.

    TMR-JWAP has a better video below.
     
    #7 alftoy, Feb 8, 2022
    Last edited: Feb 8, 2022
  8. TMR-JWAP

    TMR-JWAP Senior Member

    Joined:
    Aug 12, 2016
    6,404
    6,062
    0
    Location:
    Columbia, SC
    Vehicle:
    2007 Prius
    Model:
    Touring
    As mentioned previously, this video provides a very good procedure for vent and trim removal for these pieces. You don't need to perform any extra steps after the desired vent is removed.

     
    #8 TMR-JWAP, Feb 8, 2022
    ydpplqbd and alftoy like this.
  9. PriusCamper

    PriusCamper Senior Member

    Joined:
    Mar 3, 2012
    11,330
    4,614
    0
    Location:
    Pacific Northwest, USA
    Vehicle:
    2007 Prius
    Model:
    Two
    Just find a Prius at a wrecking yard and practice removing it there first. If you remove it without damaging it then buy it and take it home and swap it.
     
    #9 PriusCamper, Feb 8, 2022
  10. JahT

    JahT Member

    Joined:
    Dec 10, 2007
    145
    76
    0
    The one to the right of the steering wheel is super fragile at the top, don't lift the bottom like he does in the video, try to pull vent straight out from top and bottom. All tabs are parallel with the floor and the vent insert is too, so pulling straight should avoid breakage at the top part.
     
    #10 JahT, Feb 8, 2022
(You must log in or sign up to post here.)