1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Help! Codes: POA60, POA63, POA78, POAEF, P3000, P1116, P0A80, P3019, C1259, C1310, C2122, B1421

Discussion in 'Gen 2 Prius Technical Discussion' started by Mattclay, Jul 19, 2019.

  1. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    So as you can see I have a lot of codes. The first 5 pertain to the Hybrid Control, P1116 is for Engine and ECT, the next three are for the HV battery, then ABS/VSC/TRAC. The last two I'm not too worried about (lol) they are for the tire pressure and air conditioner.

    These problems started when my ABS pump actuator went out. I replaced that and it seems to be working ok. I have the red triangle light, VSC, check engine etc. The car turns on but doesn't go into drive on the first try, I usually have to turn it off and on again to get it into drive. When it's in drive, the battery does not charge properly and the car won't accelerate past like 50mph. The fan for the HV battery is constantly on, and after about 10 minutes of driving the acceleration problem gets worse, seems something is overheating. I am not driving it but this is what happened when I road tested it after replacing the pump actuator.

    The car is a 2008 with about 105k on it. The only good news is I bought a salvage Prius that is in good running condition so I can replace many parts but I don't even know where to begin. For example I don't want to swap out the HV batteries just yet even though that might solve some of the codes because the battery was working prior to the ABS pump job so something else like the inverter might be the main culprit and I don't want to damage a second battery. Any input will be greatly appreciated.
     
    #1 Mattclay, Jul 19, 2019
    Last edited: Jul 19, 2019
  2. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    Here's a screenshot.
     

    Attached Files:

    #2 Mattclay, Jul 19, 2019
  3. bobodaclown

    bobodaclown Member

    Joined:
    Feb 22, 2012
    216
    72
    0
    Location:
    USA
    Vehicle:
    2009 Prius
    Model:
    Base
    Inverter cooling pump? Easy fix.

    moto g(6) ?
     
    #3 bobodaclown, Jul 19, 2019
  4. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    24,910
    16,213
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    B1421 just says the light shining on the solar sensor wasn't very strong when you pulled the codes. No issue.

    C1259 and C1310 are just the brake ECU repeating that the hybrid control ECU has reported issues. If I remember right, P3000 from the hybrid control may just be "look! you've got battery codes", P0A80 is a common overall battery code, and P3019 may be pointing you at a particular battery block.

    To avoid relying on my memory, I'd recommend looking those up (if nothing else, just click the snowflakes next to those two, and the four P0Axx's from the hybrid control, and summarize for us what Techstream tells you they mean; that'll save us all rushing to look up your codes ourselves).
     
    #4 ChapmanF, Jul 19, 2019
  5. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    I replaced that when I did the actuator pump since the inverter was out. With the cap off of the inverter's coolant reservoir, there is a good amount of flow/turbulence so I think the new pump is good.

    Yeah I took that photo with a g6, cheap burner phone.
     
    #5 Mattclay, Jul 19, 2019
    Last edited: Jul 19, 2019
  6. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----

    Thanks Chapman. The additional info for the codes that had a 'snowflake' next to them are as follows:

    PAO60 - Drive Motor "A" Phase V Current
    POA63 - Drive Motor "A" Phase W Current
    POA78 Drive Motor "A" Inverter Performance
    POAEF 275 - Drive Motor Inverter Temperature Sensor "A" Circuit Low
    P1116 Coolant Temperature Sensor Circuit Stuck for Coolant Heat Storage System
    POA8O - Replace Hybrid Battery Pack
    P3019 - Battery Block 9 Becomes Weak
    C1310 - HV System Malfunction
     
    #6 Mattclay, Jul 19, 2019
  7. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    Is it possible I have a bad battery and an inverter problem?
     
    #7 Mattclay, Jul 19, 2019
  8. ChapmanF

    ChapmanF Senior Member

    Joined:
    Mar 30, 2008
    24,910
    16,213
    0
    Location:
    Indiana, USA
    Vehicle:
    2010 Prius
    Model:
    IV
    Well, the P0A80 (those are zeros, not Os) and P3019 paint a pretty common picture of a battery in need of replacement, with block 9 serving as the canary.

    C1310 comes from the brake ECU but only means "hey, I heard there are some codes over in the hybrid control ECU".

    That cluster of motor current and inverter performance/temperature codes is kind of fascinating, I don't think I've seen it on PriusChat before. The next place to look would be in the Repair Manual (more info), to look up each of those codes and find the workup sections for each one. On the first page of workup for each one, there will be what's called the "detection condition", which is the real explanation of what the computer saw that made it set that code. (Those Techstream one-liners like "inverter performance" are more like fortune cookies or memory jogs than useful explanations.)

    The cluster could point to an inverter problem, but that's a bit of bother to replace, so I would probably spend a little more time following through the troubleshooting workup steps before just deciding that has to be it.
     
    #8 ChapmanF, Jul 19, 2019
    JC91006 likes this.
  9. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,525
    8,428
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    I suspect the inverter was not put back properly when you replaced the brake actuator.

    And while the car was out of commission, the HV BATTERY went out of balance and failed.

    If you have the parts, replace both the inverter and hv battery. Pay special attention when you are removing it from the salvage car, so you can see if you've made an error when you reassembled your car after the repair
     
    #9 JC91006, Jul 19, 2019
    PriusGuy32 and Skibob like this.
  10. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    Good stuff, thanks again. I'll get my hands on a repair manual and try to learn more before starting. I'll follow up in a day or two.
     
    #10 Mattclay, Jul 19, 2019
  11. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    Thanks for your reply. Regarding the inverter, I had to remove it twice because the first (used) abs actuator I replaced with was also bad. The second time I had it out it got rained on when I ran to the store 5 minutes away to buy something, plus I think a couple of the small electrical connections got some rough treatment from me while removing them. It was after the second time it was out that I got all those weird new codes. I took it out a third time thinking that I must have missed a connection when I got all these codes but there were no missed or loose connections.

    I also suspect that the HV battery might have gotten messed up from the down time.
     
    #11 Mattclay, Jul 19, 2019
  12. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,525
    8,428
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    I gotta hand it to you, doing the brake actuator twice. I'm having anxiety just looking forward to my first replacement LOL.

    Did your first replacement come from a wrecked Prius?
     
    #12 JC91006, Jul 19, 2019
  13. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    Yeah it was from a junk yard. I paid like $140 for it which was kind of a red flag because most of them were in the $250 + range. To their credit they sent me a 2nd one for free. In light of the problems I had I probably would have bought one of the remans from Dorman.
     
    #13 Mattclay, Jul 19, 2019
  14. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,525
    8,428
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    This is a pretty big repair. You have to make sure all is put back together properly. Then you have to have techstream to bleed the brake system.
     
    #14 JC91006, Jul 19, 2019
  15. Mattclay

    Mattclay New Member

    Joined:
    Dec 17, 2018
    17
    1
    0
    Location:
    Usa
    Vehicle:
    2008 Prius
    Model:
    ----USA----
    Thanks again all for the advice. Its been about a week since I swapped the hybrid battery for another used one. That fixed all of the codes except for the P1116 and the code for the tire pressure sensors. I replaced the coolant control valve, that doesn't seem to have solved that problem however as I still get the code. Anyway a big improvement and happy to report there was no apparent issue with the inverter despite the codes suggesting that there was.
     
    #15 Mattclay, Jul 28, 2019
    donbright likes this.
(You must log in or sign up to post here.)