reboot kit driveshaft unclear about some things.

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by terramir, Apr 27, 2019.

  1. terramir

    terramir Member

    Joined:
    Aug 3, 2015
    318
    50
    2
    Location:
    Los Angeles
    Vehicle:
    2004 Prius
    Model:
    II
    So I need to reboot the passenger side driveshaft.
    while getting it out it fell apart so regrettably I don't have it marked while way the three way bearing is inserted. anyway to get a best guess on that part?
    also the reboot kit comes with new grease and snaprings and stuff My question here is more along the lines of cleaning the old grease so I can get a closer examination of the bearings etc. what should I use the manual is not really clear on this and I don't know if there is anything that could be damaged by carb cleaner or engine degreaser. I figure that getting the old grease is important because
    A. I need to physically check the bearings to see if there still look and feel good can't do this with the old grease still in the way.
    B. The new grease needs to not be hindered by the old broken down grease from doing it's job.
    So does anyone know what to use to clean the bearings so I can inspect and well reassemble after.
    terramir
     
    #1 terramir, Apr 27, 2019
  2. Mendel Leisk

    Mendel Leisk Senior Member

    Joined:
    Oct 17, 2010
    57,957
    39,988
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    Some Repair Manual info:
     

    Attached Files:

    #2 Mendel Leisk, Apr 27, 2019
    terramir likes this.
  3. padroo

    padroo Senior Member

    Joined:
    Jan 11, 2008
    2,763
    2,251
    13
    Location:
    Chesterton, Indiana Another third world country.
    Vehicle:
    2016 Prius
    Model:
    Four
    I assume it has a lot of miles on it, I would replace the whole unit with a reman, they are so cheap.
     
    #3 padroo, Apr 27, 2019
    Mendel Leisk likes this.
  4. terramir

    terramir Member

    Joined:
    Aug 3, 2015
    318
    50
    2
    Location:
    Los Angeles
    Vehicle:
    2004 Prius
    Model:
    II
    Thanks I have the whole manual, so yeah I got this, but it there it says nothing about cleaning like mechanics already know how to so they didn't write this in.
    This is why I'm asking.
    terramir
     
    #4 terramir, Apr 27, 2019
    Mendel Leisk likes this.
  5. terramir

    terramir Member

    Joined:
    Aug 3, 2015
    318
    50
    2
    Location:
    Los Angeles
    Vehicle:
    2004 Prius
    Model:
    II
    I bought one of those it was missing the dampener, so the whole thing is out of balance so now if I drive faster than 60 I get 3 warning lights on the dash board (!) ABS VSC
    terramir
     
    #5 terramir, Apr 27, 2019
  6. Mendel Leisk

    Mendel Leisk Senior Member

    Joined:
    Oct 17, 2010
    57,957
    39,988
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    Ah ok.
     
    #6 Mendel Leisk, Apr 27, 2019
    Last edited: Apr 27, 2019
  7. terramir

    terramir Member

    Joined:
    Aug 3, 2015
    318
    50
    2
    Location:
    Los Angeles
    Vehicle:
    2004 Prius
    Model:
    II
    My car was driving better with the old shaft the only reason I replaced it was a boot leak. regret this decision should have just left it there and used a split boot kit. but to late now to do anything about it. besides rebuild the drive shaft.
    What is the safest way to remove the old grease?????
    terramir
     
    #7 terramir, Apr 27, 2019
  8. padroo

    padroo Senior Member

    Joined:
    Jan 11, 2008
    2,763
    2,251
    13
    Location:
    Chesterton, Indiana Another third world country.
    Vehicle:
    2016 Prius
    Model:
    Four
    Did you take it back?
     
    #8 padroo, Apr 27, 2019
  9. terramir

    terramir Member

    Joined:
    Aug 3, 2015
    318
    50
    2
    Location:
    Los Angeles
    Vehicle:
    2004 Prius
    Model:
    II
    Lol I bought this shaft on ebay like 3 years ago just got around to changing it so no warranty for the POS Detroit axle rebuild.
    But I can fix mine just need to know what I should use to clean the old grease off so I can assess the condition of the bearings.
    terramir
     
    #9 terramir, Apr 27, 2019
  10. Mendel Leisk

    Mendel Leisk Senior Member

    Joined:
    Oct 17, 2010
    57,957
    39,988
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    I'll bite: kerosene? IIRC that was recommended for motorcycle chain cleaning, and they have rubber o-rings.
     
    #10 Mendel Leisk, Apr 27, 2019
  11. padroo

    padroo Senior Member

    Joined:
    Jan 11, 2008
    2,763
    2,251
    13
    Location:
    Chesterton, Indiana Another third world country.
    Vehicle:
    2016 Prius
    Model:
    Four
    I agree with Mendel or any strong solvent that will remove all the old contaminated grease.
    Some of the new approved solvents they sell for the DIY people are just a fraction of the strength of the old days.
    Years ago when I worked in the steel mill we had stuff that would disolve screwdriver handles.
     
    #11 padroo, Apr 27, 2019
  12. The Critic

    The Critic Resident Critic

    Joined:
    Oct 28, 2005
    3,193
    2,325
    0
    Location:
    CA
    Vehicle:
    2011 Prius
    Model:
    Three
    Don’t use solvent. It is almost impossible to get it fully rinsed out of the outer joint. Just wipe up as much grease as you can replace with new.

    If there is actual debris in the joint then the joint is not worth rebooting. Just my opinion...
     
    #12 The Critic, Apr 28, 2019
    Raytheeagle likes this.
  13. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,200
    6,489
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    I would use brake parts cleaner to clean metal parts, but not use that on rubber parts that need cleaning.
     
    #13 Patrick Wong, Apr 28, 2019
    padroo likes this.
  14. padroo

    padroo Senior Member

    Joined:
    Jan 11, 2008
    2,763
    2,251
    13
    Location:
    Chesterton, Indiana Another third world country.
    Vehicle:
    2016 Prius
    Model:
    Four
    If all else fails you could follow the manufacturers directions, either the boot manufacturer or Toyota's.
     
    #14 padroo, Apr 28, 2019
  15. terramir

    terramir Member

    Joined:
    Aug 3, 2015
    318
    50
    2
    Location:
    Los Angeles
    Vehicle:
    2004 Prius
    Model:
    II
    Well the boots are being replaced after cleaning so rubber parts should not be the issue. Are the bearings on both sides all metal??? Anyone know ??
    terramir
     
    #15 terramir, Apr 28, 2019
  16. Mendel Leisk

    Mendel Leisk Senior Member

    Joined:
    Oct 17, 2010
    57,957
    39,988
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    If it's just metal I think you can go nuts?
     
    #16 Mendel Leisk, Apr 28, 2019
    padroo likes this.
  17. The Critic

    The Critic Resident Critic

    Joined:
    Oct 28, 2005
    3,193
    2,325
    0
    Location:
    CA
    Vehicle:
    2011 Prius
    Model:
    Three
    The bearings are metal. But even after removing the balls in the outer joint you cannot fully clean out the housing. This is why I only suggest soaking up the old grease with clean rags.
     
    #17 The Critic, Apr 30, 2019
    Mendel Leisk likes this.
(You must log in or sign up to post here.)