1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Key Fob Buttons Not Working (But All Other Functions Are Fine)

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by dangr, Apr 6, 2016.

Tags:
  1. dangr

    dangr Junior Member

    Joined:
    Apr 20, 2014
    5
    0
    0
    Location:
    Los Angeles, California
    Vehicle:
    2005 Prius
    Model:
    II
    Hi there!

    I just replaced the batteries in my two key fobs, one of which just ran out, and the other ran out a long time ago but I was too lazy to replace it. One of them now works great, and the other one is... almost there. I can use all the smart key functions (keyless entry, engine start without putting the key in the docking thing, etc.) but none of the buttons (lock, unlock, panic) actually work on the fob. Is there some way to reset this, or any thoughts on what might have happened?

    Thanks so much!
     
    #1 dangr, Apr 6, 2016
  2. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,530
    8,429
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    Maybe 1 of the 3 buttons is stuck.....see if they all click when you press down on them?
     
    #2 JC91006, Apr 6, 2016
  3. dangr

    dangr Junior Member

    Joined:
    Apr 20, 2014
    5
    0
    0
    Location:
    Los Angeles, California
    Vehicle:
    2005 Prius
    Model:
    II
    Interesting point — the unlock and lock click, but the panic one does not...
     
    #3 dangr, Apr 6, 2016
  4. JC91006

    JC91006 Senior Member

    Joined:
    Nov 10, 2013
    16,530
    8,429
    0
    Location:
    Los Angeles, CA
    Vehicle:
    2008 Prius
    Model:
    II
    get an exacto knife or a very sharp object and try to dislodge the button. Once it gets unstuck, your buttons will work again.
     
    #4 JC91006, Apr 6, 2016
  5. dangr

    dangr Junior Member

    Joined:
    Apr 20, 2014
    5
    0
    0
    Location:
    Los Angeles, California
    Vehicle:
    2005 Prius
    Model:
    II
    So, good and bad news — I nudged the button around with my finger, and it sort of snapped back into place. The lock and unlock buttons work now! However, the red part of the other button pretty much immediately fell off, so I guess I'll have to glue it back on. Not a huge deal because I never use that button anyway, but thanks so much for the quick response! This was perfect.
     
    #5 dangr, Apr 6, 2016
  6. Jls

    Jls New Member

    Joined:
    May 23, 2018
    2
    0
    0
    Location:
    Tucson, AZ
    Vehicle:
    2005 Prius
    Model:
    Three
    Thank you. This fixed my problem. Miami just need to get a second remote and program it.
     
    #6 Jls, May 23, 2018
  7. RobertK

    RobertK Member

    Joined:
    Sep 9, 2007
    128
    40
    0
    Location:
    Norfolk, VA
    Vehicle:
    2007 Prius
    Model:
    N/A
    Sounds like you need a new case for your fob. They cost about $12.00, and you just move the electronics to the new case. Much easier and cheaper than programming a new remote.
     
    #7 RobertK, May 23, 2018
  8. RobH

    RobH Senior Member

    Joined:
    Sep 18, 2006
    2,369
    981
    70
    Location:
    Sunnyvale, California
    Vehicle:
    2006 Prius
    Be sure to transfer the transponder chip as well as the circuit board to a new case.
     
    #8 RobH, May 24, 2018
  9. Isaac Starkey

    Isaac Starkey New Member

    Joined:
    Sep 19, 2018
    1
    0
    0
    Location:
    Wisconsin
    Vehicle:
    2005 Prius
    Model:
    Base
    My housing was replaced by the prior owner and apparently he forgot to swap the chip. I have a SKS fob so it still starts but if the battery dies in the fob I’m screwed. Anyone have a source I can buy the chip from that never got swapped to the new housing?
     
    #9 Isaac Starkey, Sep 19, 2018
(You must log in or sign up to post here.)