1. Attachments are working again! Check out this thread for more details and to report any other bugs.

12 VOLT DIAGNOSTIC CHECK

Discussion in 'Prius c Care, Maintenance and Troubleshooting' started by Andyprius1, Nov 30, 2014.

  1. Andyprius1

    Andyprius1 Senior Member

    Joined:
    Feb 4, 2013
    2,327
    859
    1
    Location:
    Cool CA
    Vehicle:
    2017 Prius Prime
    Model:
    Plug-in Base
    ON THE GEN 2 and 3 a procedure can be done to show the level of the 12V battery, does the
    Prius C have this?
     
    #1 Andyprius1, Nov 30, 2014
  2. ztanos

    ztanos All-around Geek!

    Joined:
    Jan 10, 2013
    3,339
    1,150
    40
    Location:
    Cumming, Georgia
    Vehicle:
    2012 Prius c
    Model:
    Four
    Most likely. I can see my voltage with my torque app.
     
    #2 ztanos, Dec 2, 2014
  3. purplebutterfly

    purplebutterfly New Member

    Joined:
    Dec 3, 2014
    2
    3
    0
    Location:
    bowdon ga
    Vehicle:
    2012 Prius c
    Model:
    N/A
    You can enter the "system menu mode" by powering the car up in accessory, then while holding the "car" button, turn the lights on and off three times. That will put the computer in the system menu mode. Once in there press the "function check/setting" button, then press "vehicle signal" button. Then that will bring up a screen where you can read the 12 volt battery voltage. To get out of that mode, hold down the setup button and the computer will reboot. Hope that helps.
     
    #3 purplebutterfly, Dec 3, 2014
    minkus and Andyprius1 like this.
  4. bisco

    bisco cookie crumbler

    Joined:
    May 11, 2005
    110,133
    50,050
    0
    Location:
    boston
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    reboot? i think andy may be in love!:p
     
    #4 bisco, Dec 3, 2014
    Andyprius1 likes this.
  5. Easy Rider 2

    Easy Rider 2 Senior Member

    Joined:
    Aug 5, 2014
    1,584
    257
    0
    Location:
    Ocala, FL
    Vehicle:
    2013 Prius c
    Model:
    Three
    WOW. Where have you been the past few years ???:)
    Good post.

    I think most people talking about monitoring the 12 V system voltage are doing it with a scan tool though.
     
    #5 Easy Rider 2, Dec 3, 2014
  6. purplebutterfly

    purplebutterfly New Member

    Joined:
    Dec 3, 2014
    2
    3
    0
    Location:
    bowdon ga
    Vehicle:
    2012 Prius c
    Model:
    N/A
    I just bought this car about a month ago. There is a lot to learn. I played one day and found that menu. I also found if you follow the same routine but hold down the "setup" button instead. It brings you into a diagnostic menu. I didn't see much useful info in either one. I'm sure there are more secret menu's, we just need to play.
     
    #6 purplebutterfly, Dec 5, 2014
    Andyprius1 likes this.
  7. Andyprius1

    Andyprius1 Senior Member

    Joined:
    Feb 4, 2013
    2,327
    859
    1
    Location:
    Cool CA
    Vehicle:
    2017 Prius Prime
    Model:
    Plug-in Base
    I'll try that. TY
     
    #7 Andyprius1, Dec 5, 2014
  8. Andyprius1

    Andyprius1 Senior Member

    Joined:
    Feb 4, 2013
    2,327
    859
    1
    Location:
    Cool CA
    Vehicle:
    2017 Prius Prime
    Model:
    Plug-in Base
    . Depending on the type of reboot.
     
    #8 Andyprius1, Dec 5, 2014
    bisco likes this.
  9. jdcollins5

    jdcollins5 Senior Member

    Joined:
    Aug 30, 2009
    5,131
    1,340
    0
    Location:
    Wilmington, NC
    Vehicle:
    2010 Prius
    Model:
    III
    One recommendation for using the system menu to monitor your 12V battery. The first time that you use it, first measure your 12V with a meter either directly on the battery posts or the jump point in the engine fuse box. The difference between my 12V battery and the system menu was - 0.7 V.

    I thought I had a bad battery until I measured it at the battery terminals.
     
    #9 jdcollins5, Dec 5, 2014
    Andyprius1 likes this.
  10. Andyprius1

    Andyprius1 Senior Member

    Joined:
    Feb 4, 2013
    2,327
    859
    1
    Location:
    Cool CA
    Vehicle:
    2017 Prius Prime
    Model:
    Plug-in Base
    Neither system worked, I have a model 2, you may. Have a 3 or higher. The only car on my dash / wheel is for re-
    Circulation.
     
    #10 Andyprius1, Dec 5, 2014
  11. Andyprius1

    Andyprius1 Senior Member

    Joined:
    Feb 4, 2013
    2,327
    859
    1
    Location:
    Cool CA
    Vehicle:
    2017 Prius Prime
    Model:
    Plug-in Base
    I see you do have a Model III, My car has what resembles a actual Ignition key, and works like one, except the rest is pure Prius w/ Ready light, ect.
     
    #11 Andyprius1, Dec 5, 2014
  12. Easy Rider 2

    Easy Rider 2 Senior Member

    Joined:
    Aug 5, 2014
    1,584
    257
    0
    Location:
    Ocala, FL
    Vehicle:
    2013 Prius c
    Model:
    Three
    Which really is the best way to do it anyway.
    A respectable meter can be had a lot of places for about $10.
     
    #12 Easy Rider 2, Dec 6, 2014
    jdcollins5 likes this.
(You must log in or sign up to post here.)