1. Attachments are working again! Check out this thread for more details and to report any other bugs.

No More Center Console Rattle

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by GSW, Mar 14, 2011.

Page 1 of 2
  1. GSW

    GSW PRIUS POWER

    Joined:
    Jul 7, 2009
    537
    74
    0
    Location:
    Jacksonville
    Vehicle:
    2010 Prius
    Model:
    II
    I don't know who suggested inserting a mouse pad between the upper floating bridge console and the lower support bridge, but it worked great. Just had to trim the black mouse pad in a U shape so it would disappear inside. Unbolt the console (5 bolts), move the console compartment back exposing 4 more bolts (2 on the sides, 2 under the cup holder) Loosen those. Using the 2 little arms on the U shape, just slide it between the bridge. Just bolt everything back together and do not over tighten. Pretty simple.

    This is an EXAMPLE using FELT instead of the mouse pad which I used. I just preferred to trim the pad back so you couldn't see it at all when reassembled. Thanks to member MMichaell for the loan on his console picture.

    [​IMG][/QUOTE]
     
    #1 GSW, Mar 14, 2011
    2 people like this.
  2. airgas1998

    airgas1998 New Member

    Joined:
    Mar 4, 2011
    78
    5
    0
    Location:
    iowa
    Vehicle:
    2011 Prius
    Model:
    Two
    [/QUOTE]


    gee,Toyota see this is all you need to do. don't you (toyota) dumbasses test drive your vehicles.
     
    #2 airgas1998, Mar 14, 2011
  3. markderail

    markderail I do 45 mins @ 3200 PSI

    Joined:
    Sep 13, 2006
    2,260
    163
    18
    Location:
    Pierrefonds (Montreal) Quebec Canada
    Vehicle:
    2010 Prius
    Model:
    N/A
    Thanks I will try, will be cheaper to try than switching to the CT200h...
     
    #3 markderail, Mar 14, 2011
  4. geeter

    geeter Member

    Joined:
    Apr 11, 2010
    208
    16
    0
    Location:
    Chicago
    Vehicle:
    2010 Prius
    Model:
    II
    Definately need to try that one. Drives me nuts on a cold morning.
     
    #4 geeter, Mar 14, 2011
  5. mmichaell

    mmichaell Member

    Joined:
    Dec 16, 2009
    241
    18
    0
    Location:
    chicago
    Vehicle:
    2010 Prius
    Model:
    III
    [/QUOTE]


    This example (with felt) is actually my car/photo. But it did not work well - you really need to stick something that absorbs shock in the middle. I went with that weight-lifting padding that you find at gyms, that you put your weights on, sit on, etc. Like a mousepad it works great.
     
    #5 mmichaell, Mar 14, 2011
    1 person likes this.
  6. GSW

    GSW PRIUS POWER

    Joined:
    Jul 7, 2009
    537
    74
    0
    Location:
    Jacksonville
    Vehicle:
    2010 Prius
    Model:
    II
    Michael, again, thanks for the picture and your input. Luckily I had an old mouse pad and everything went back together well. I can't believe the difference it has made to a much quieter car. Apparently the console had me tricked into believing there were more rattles, but just turned out to be the console. Funny thing about noise or rattles is they are so hard to find, especially while driving.
     
    #6 GSW, Mar 14, 2011
  7. airgas1998

    airgas1998 New Member

    Joined:
    Mar 4, 2011
    78
    5
    0
    Location:
    iowa
    Vehicle:
    2011 Prius
    Model:
    Two
    well thx to you guys this worked. it is quiet as a "mouse" no pun intended. now i just need to isolate my other two problem areas front left dash and front right.
     
    #7 airgas1998, Mar 16, 2011
  8. phoenixgreg

    phoenixgreg Senior member

    Joined:
    Apr 7, 2010
    1,157
    290
    66
    Location:
    Phoenix
    Vehicle:
    2010 Prius
    Model:
    II
    BIG +1 to that!!!!
     
    #8 phoenixgreg, Mar 16, 2011
  9. spiderman

    spiderman wretched

    Joined:
    Jul 5, 2009
    7,543
    1,558
    0
    Location:
    Alaska
    Vehicle:
    2010 Prius
    Model:
    II
    I don't know, this modification could have a serious impact on your fuel economy.
     
    #9 spiderman, Mar 16, 2011
  10. airgas1998

    airgas1998 New Member

    Joined:
    Mar 4, 2011
    78
    5
    0
    Location:
    iowa
    Vehicle:
    2011 Prius
    Model:
    Two
    i'm willing to take that risk....:D
     
    #10 airgas1998, Mar 16, 2011
  11. chakrax

    chakrax Junior Member

    Joined:
    Dec 17, 2010
    24
    8
    1
    Location:
    San Jose, CA
    Vehicle:
    2010 Prius
    Model:
    II
    Thanks to this thread, the rattle in my 2010 Prius II is gone. I did not have a mousepad handy, so I used some kitchen shelf liner - the one that's like a sheet of foam rubber. I also did not do the entire U shape, just the strip at the top. It was a bit hard to figure out where to put the strip. There is an indented area that is deeper than the edges, and that seemed to be the best place for it. I put it back together and I can report that the rattle is gone. Too bad the photos in this thread are no longer available. That would have helped me.
     
    #11 chakrax, Nov 16, 2011
  12. Caug1

    Caug1 Member

    Joined:
    May 6, 2011
    119
    9
    0
    Location:
    BOSTON
    Vehicle:
    2010 Prius
    Model:
    III
    [/QUOTE]
    I cant open up the images.
     
    #12 Caug1, Nov 19, 2011
  13. bnaccs

    bnaccs bnaccs

    Joined:
    Dec 9, 2007
    191
    10
    1
    Location:
    Colorado
    Vehicle:
    2010 Prius
    Model:
    III
    People should not have to be putting items in areas of their new cars to stop them from rattling. I am disappointed in Toyota!
     
    #13 bnaccs, Nov 20, 2011
  14. DetPrius

    DetPrius Active Member

    Joined:
    Apr 24, 2009
    545
    92
    0
    Location:
    Southeast Michigan
    Vehicle:
    2010 Prius
    Model:
    III
    I sure wish I could see the pictures! I'm nearing a cross country drive and would love to do this mod. I'll look and see if i can find the bolts described. Yes bnaccs, we should not have to do this, but I will do it to fix the problem.
     
    #14 DetPrius, Nov 20, 2011
  15. mediahound

    mediahound Active Member

    Joined:
    Aug 7, 2013
    903
    155
    2
    Location:
    SF Bay Area, California
    Vehicle:
    2013 Prius
    Model:
    Four
    I know this is an old post but for my reference, does anyone have the pictures? They are not loading.
     
    #15 mediahound, Jan 30, 2014
  16. Dan Smith

    Dan Smith New Member

    Joined:
    May 28, 2014
    1
    0
    0
    Vehicle:
    2010 Prius
    Model:
    Four
    Does anyone have pictures or diagrams or video?
    THX
     
    #16 Dan Smith, May 28, 2014
  17. phoenixgreg

    phoenixgreg Senior member

    Joined:
    Apr 7, 2010
    1,157
    290
    66
    Location:
    Phoenix
    Vehicle:
    2010 Prius
    Model:
    II
    Dan, Priuschat has gone thru a couple of upgrades since these pictures were posted. It seems for each upgrade, more images are lost. It could be that if a previous member has dropped PC, all of his pictures go away too.
     
    #17 phoenixgreg, May 28, 2014
  18. KennyGS

    KennyGS Senior Member

    Joined:
    Mar 28, 2014
    1,243
    1,044
    1
    Location:
    Keystone State
    Vehicle:
    2014 Prius
    Model:
    Five
    This site's admins/mods, who've been given permission, should be backing up images from DIY's - even putting PC watermarks on them to ensure they'll always be available.
     
    #18 KennyGS, May 28, 2014
  19. phoenixgreg

    phoenixgreg Senior member

    Joined:
    Apr 7, 2010
    1,157
    290
    66
    Location:
    Phoenix
    Vehicle:
    2010 Prius
    Model:
    II
    Agreed, my thinking is if it ain't broke, don't fix it! I've kept all of my images so I can re-upload anything lost here due to the upgrade.
     
    #19 phoenixgreg, May 29, 2014
  20. ny_rob

    ny_rob Senior Member

    Joined:
    Feb 28, 2012
    1,968
    813
    0
    Location:
    L.I.- NY
    Vehicle:
    Other Hybrid
    Model:
    N/A
    You just shove some material (I used the fuzzy half of a heavy duty velcro strip) in the gap between the cup holder and beginning of the fly bridge. It worked for me too....
     
    #20 ny_rob, May 29, 2014
(You must log in or sign up to post here.)
Page 1 of 2