1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Dead Leaf Stuck In Crevice

Discussion in 'Gen 3 Prius Care, Maintenance & Troubleshooting' started by crellion, Dec 6, 2013.

  1. crellion

    crellion Junior Member

    Joined:
    Sep 22, 2010
    48
    0
    0
    Location:
    USA
    Vehicle:
    2012 Prius
    Model:
    Two
    Talk about annoying, I have a dead leaf stuck in my Prius bumper crevice. When I tried to get it out, the thing just fell into the bumper crevice, and now there may not be a way to get it out but to remove the entire rear bumper!

    Anybody have recommendations of what I should do? Or should I just leave it be? Will the leaf decompose/disintegrate after a while?
     
  2. GrGramps

    GrGramps Active Member

    Joined:
    Jan 15, 2009
    294
    176
    0
    Location:
    Western North Carolina
    Vehicle:
    2012 Prius v wagon
    Model:
    N/A
    Think about it ... If leaves didn't decompose, they would be a greater threat than global warming!;)
     
    ftl likes this.
  3. ETC(SS)

    ETC(SS) The OTHER One Percenter.....

    Joined:
    Oct 28, 2010
    7,856
    6,658
    0
    Location:
    Redneck Riviera (Gulf South)
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    "leave" it.
     
    mrstop likes this.
  4. mrbigh

    mrbigh Prius Absolutum Dominium

    Joined:
    Sep 6, 2005
    3,686
    699
    2
    Location:
    Long Island, NY
    Vehicle:
    Other Electric Vehicle
    Get a large craw bar and pry the darn thing from inside the rear bumper,..... NOT:p
     
  5. Mike500

    Mike500 Senior Member

    Joined:
    Mar 1, 2012
    2,593
    764
    0
    Vehicle:
    2012 Prius v wagon
    Model:
    Two
    LEAF it!
     
  6. ems2158

    ems2158 Active Member

    Joined:
    Dec 30, 2012
    221
    162
    0
    Location:
    Bucks County, PA
    Vehicle:
    2017 Prius Prime
    Model:
    Prime Advanced
    I had a funny "leaf" incident. Last week while driving over 40 mph, I was getting an annoying buzzing/fluttering noise. I had the windshield replaced a few weeks earlier and was concerned that the windshield was not sealed properly. A maple leaf seed, the kind that look like little helicopters when they fall off the tree, was lodged between the bottom edge of the glass and the A pillar. I had to pull it out with tweezers. Noise gone! It was making me crazy for 2 days.

    Have to remember to vacuum or hose the leaves out from the base of the windshield and wipers.

    I wouldn't worry too much about the leave in the bumper crevice.
     
  7. car compulsive

    car compulsive Active Member

    Joined:
    Aug 6, 2011
    741
    274
    0
    Location:
    Michigan
    Vehicle:
    2011 Prius
    Model:
    Two
    I had this mental picture of a Nissan stuck between a rock and a hard place.
     
    milesmutt likes this.
  8. milesmutt

    milesmutt Junior Member

    Joined:
    Nov 9, 2013
    34
    5
    0
    Location:
    Silicon Valley, CA
    Vehicle:
    2010 Prius
    Model:
    III

    I own a Leaf and that's the first thing I thought, lol.
     
  9. Former Member 68813

    Former Member 68813 Senior Member

    Joined:
    Oct 3, 2010
    3,524
    981
    8
    Location:
    US
    Vehicle:
    Other Hybrid
    Model:
    N/A
    The good news is the leaf is dead. Otherwise, I would worry.
     
  10. Mike500

    Mike500 Senior Member

    Joined:
    Mar 1, 2012
    2,593
    764
    0
    Vehicle:
    2012 Prius v wagon
    Model:
    Two
    The leaf is NEVER dead, until it is entirely gone. When it turns brown, the photosynthetic systems within the leaf stop functioning. Then, other mold and microorganisms are ALIVE on the leaf to cause it to decay. Death occurs when every remnant of the leaf is gone.
     
  11. Mendel Leisk

    Mendel Leisk EGR Fanatic

    Joined:
    Oct 17, 2010
    56,678
    39,222
    80
    Location:
    Greater Vancouver, British Columbia, Canada
    Vehicle:
    2010 Prius
    Model:
    Touring
    We tend to get pine needles building up behind the air foil on the hatch. I'll pick out what I can with tweezers, hit it with high pressure water when washing, and leaf blower when drying. You can also use a thin strip of cloth and "floss" some zones.

    Other than that, not much you can, short of disassembly.

    One place to check periodically: the hatch gasket, it can accumulate stuff. Be careful: it has some sort of black tacky adhesive in places.