1. Attachments are working again! Check out this thread for more details and to report any other bugs.

How Toyota managed to stack the HV and 12V battery under the back seat

Discussion in 'Prius c Main Forum' started by Mister MMT, Feb 16, 2012.

  1. Mister MMT

    Mister MMT Active Member

    Joined:
    Feb 9, 2012
    285
    142
    0
    Location:
    Germany
    Vehicle:
    2009 Prius
    Model:
    N/A
    This image shows the terrific job done by the Toyota engineers fitting both the HV and 12 V battery, but also the gas tank (shrunk to 36 l from 42 in the Yaris). All that is encaged by metal protections to protect from side impacts.

    [​IMG]

    The 12 V battery is accessible through a removable cover

    [​IMG]


    [​IMG]

    Nice job and worth noting!
     
    #1 Mister MMT, Feb 16, 2012
  2. usbseawolf2000

    usbseawolf2000 HSD PhD

    Joined:
    Sep 22, 2004
    14,487
    3,000
    0
    Location:
    Fort Lee, NJ
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    The metal cage also serves as the support for the rear seats. Very clever packaging.
     
    #2 usbseawolf2000, Feb 16, 2012
  3. jadziasman

    jadziasman Prius owner emeritus

    Joined:
    Jan 17, 2011
    1,355
    487
    0
    Location:
    District 6
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    That back seat cushion had better be REALLY strong. Imagine kids or teens bouncing on the seat and damaging something in that cage.

    I'm sure that Toyota has tested the configuration and found it impervious to this type of neglect. Then again, you never know.

    We will see how well it works soon enough.
     
    #3 jadziasman, Feb 16, 2012
  4. strongbad

    strongbad Member

    Joined:
    Oct 19, 2011
    170
    47
    0
    Location:
    Driggs, ID
    Vehicle:
    Other Non-Hybrid
    Model:
    N/A
    Someone help me understand why the Prius C needs the 12v battery. It's lead-acid, is it not? I know that lights and low-power electronics are all 12V, but why is a battery needed for the 12V loads and not just a buck converter for the high-voltage NMH battery?
     
    #4 strongbad, Feb 16, 2012
  5. usbseawolf2000

    usbseawolf2000 HSD PhD

    Joined:
    Sep 22, 2004
    14,487
    3,000
    0
    Location:
    Fort Lee, NJ
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Base
    HV battery gets disconnected when you turn it off. 12v lead acid battery is used to boot up computers to get to READY state.
     
    #5 usbseawolf2000, Feb 16, 2012
  6. dhanson865

    dhanson865 Expert and Devil's advocate

    Joined:
    May 24, 2011
    851
    188
    0
    Location:
    TN, USA
    Vehicle:
    2005 Prius
    Interesting views but I don't see mention of the vent tube. Is it vented?
     
    #6 dhanson865, Feb 16, 2012
  7. austingreen

    austingreen Senior Member

    Joined:
    Nov 3, 2009
    13,602
    4,136
    0
    Location:
    Austin, TX, USA
    Vehicle:
    2018 Tesla Model 3
    Model:
    N/A
    The accessories -lights, stereo, etc - are powered @12v as well as the start button. There is a voltage converter to recharge the 12V battery. Because it is sealed to be inside the car it is much more expensive to replace even though it has a much lower load than a normal 12V car battery.

    I'm surprised they didn't find some room under the hood for a less expensive part. That would give normal jump points, so I wouldn't have had to read my manual and hunted with a flashlight when mine died. Does anyone know why its under the seat and not under the hood in the c? I understand it may be for weight balance in the lift back.
     
    #7 austingreen, Feb 16, 2012
  8. fuzzy1

    fuzzy1 Senior Member

    Joined:
    Feb 26, 2009
    17,557
    10,324
    90
    Location:
    Western Washington
    Vehicle:
    Other Hybrid
    Model:
    N/A
    This high voltage disconnect is, in part, a safety feature for crash responders and service techs.
     
    #8 fuzzy1, Feb 17, 2012
    2 people like this.
(You must log in or sign up to post here.)