1. Attachments are working again! Check out this thread for more details and to report any other bugs.

2008 Prius Headlight Assembly Replacement

Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by davidford111, Dec 22, 2010.

  1. davidford111

    davidford111 New Member

    Joined:
    Dec 22, 2010
    2
    0
    0
    Location:
    Helotes, TX
    Vehicle:
    2008 Prius
    Model:
    N/A
    The drivers side headlight assembly on my 2008 Prius has moisture in it. I have 52,000 miles on the car, so I do not think it is covered under warranty. What / how can you replace the headlight assembly?
     
    #1 davidford111, Dec 22, 2010
  2. KK6PD

    KK6PD _ . _ . / _ _ . _

    Joined:
    Mar 24, 2008
    4,003
    946
    118
    Location:
    Los Angeles Foothills
    Vehicle:
    Other Hybrid
    Model:
    N/A
    Unplug it, unscrew it, remove it, have the replacement handy, from Salvage, Internet Purchase, or direct from Toyota. Just make sure you purchase the same headlght assy as HID and Halogen are different units. Reverse disassembly, you are good to go. Oh BTW, save or reuse the old bulbs!
    I realise that this sounds oversimplfied, it actually is not!!
     
    #2 KK6PD, Dec 22, 2010
  3. davidford111

    davidford111 New Member

    Joined:
    Dec 22, 2010
    2
    0
    0
    Location:
    Helotes, TX
    Vehicle:
    2008 Prius
    Model:
    N/A
    Thanks for the feedback. One question - some of the posts I have found on the internet say you have to remove the bumper and the liner inside the wheel well to get to the screws to remove it. Is that the case or are the screws accessible without removing those other items?
     
    #3 davidford111, Dec 23, 2010
  4. Patrick Wong

    Patrick Wong DIY Enthusiast

    Joined:
    Mar 8, 2008
    18,200
    6,482
    0
    Location:
    Green Valley, AZ
    Vehicle:
    2015 Prius
    Model:
    Two
    You will need to partially remove the bumper cover so that you can access one screw that is hidden by the cover.
     
    #4 Patrick Wong, Dec 23, 2010
  5. tf4624

    tf4624 Active Member

    Joined:
    Dec 4, 2009
    526
    51
    0
    Location:
    USA
    Vehicle:
    2008 Prius
    Model:
    N/A
    No need to replace it Take Bumper off and unscrew the few screws that hold it in and pull it off.. Once you have that done.. Take out bulbs.(don't touch lenses) with fingers.. use gloves

    Then heat the seals up around the unit and pull it apart.. Dry it out with a dryer and re glue and re seal so moisture doesn't get in. Bam.. Done
     
    #5 tf4624, Dec 28, 2010
  6. lvthehun

    lvthehun New Member

    Joined:
    Jan 2, 2011
    3
    0
    0
    Location:
    Las Vegas
    Vehicle:
    2008 Prius
    Model:
    N/A
    [/ATTACH]Anyone know why the replacement asy on the internet not the same as in the car. I LOOKED ALL OVER ONLINE. They are all the same see pictures.
    Thanks to help me on this
     

    Attached Files:

    #6 lvthehun, Jan 2, 2011
  7. KK6PD

    KK6PD _ . _ . / _ _ . _

    Joined:
    Mar 24, 2008
    4,003
    946
    118
    Location:
    Los Angeles Foothills
    Vehicle:
    Other Hybrid
    Model:
    N/A
    First off, do you have the Halogen, or HID lamps??
    They are different housings, a little more info would be nice!!!
     
    #7 KK6PD, Jan 2, 2011
  8. lvthehun

    lvthehun New Member

    Joined:
    Jan 2, 2011
    3
    0
    0
    Location:
    Las Vegas
    Vehicle:
    2008 Prius
    Model:
    N/A
    HID for sure. Because the housing holds the Ballast and a small motor. And for info I ordered the parts from autowarehouse and they sent me hallogen housing and bulb.
     
    #8 lvthehun, Jan 2, 2011
(You must log in or sign up to post here.)