1. Attachments are working again! Check out this thread for more details and to report any other bugs.

Lower Rocker Moldings, chrome

Discussion in 'Gen 3 Prius Accessories and Modifications' started by prius2x, Jun 13, 2009.

  1. Mr. D

    Mr. D Junior Member

    Joined:
    Aug 8, 2010
    36
    2
    3
    Location:
    Indiana
    Vehicle:
    2010 Prius
    Model:
    V
    There was only one style and one color when I bought mine. I have never seen another color.......ever
     
    1 person likes this.
  2. peterjmc

    peterjmc Ping pong in Ding Dang...

    Joined:
    Dec 5, 2010
    917
    189
    0
    Location:
    Clarksburg, MD
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Advanced
    Funny. They just walked up and told me that there is only one color. They were confused and thought I wanted the door edge guard moldings installed.
     
  3. Heffalump's Prius

    Heffalump's Prius Junior Member

    Joined:
    Dec 4, 2010
    29
    0
    0
    Location:
    CA
    Vehicle:
    2010 Prius
    Model:
    III
    here is my picture of the lower rocker molding!
    <a href="http://s152.photobucket.com/albums/s196/hcali_2007/?action=view&amp;current=photo-3.jpg" target="_blank"><img src="http://i152.photobucket.com/albums/s196/hcali_2007/photo-3.jpg" border="0" alt="lower rocker molding"></a>
     
  4. Trieu's_2010_Prius

    Trieu's_2010_Prius New Member

    Joined:
    Jul 3, 2010
    8
    1
    0
    Location:
    Twin Cities, MN
    Vehicle:
    2010 Prius
    Model:
    III
    As far as I know there is only one color. They might have a new color for 2011, but my local Toyota dealer in the Twin Cities haven't heard of it either.

     
  5. peterjmc

    peterjmc Ping pong in Ding Dang...

    Joined:
    Dec 5, 2010
    917
    189
    0
    Location:
    Clarksburg, MD
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Advanced
    Dealer installed them and I just got around to looking at them up close today... They don't look like they are installed right :( There is a little part at the bottom of the door that isn't actually covered by the molding.

    Does anyone have the install instructions in PDF format? Or could someone scan this for me?
     
  6. Trieu's_2010_Prius

    Trieu's_2010_Prius New Member

    Joined:
    Jul 3, 2010
    8
    1
    0
    Location:
    Twin Cities, MN
    Vehicle:
    2010 Prius
    Model:
    III
    Why don't you post the pictures so we can see if it's done correctly?


     
  7. peterjmc

    peterjmc Ping pong in Ding Dang...

    Joined:
    Dec 5, 2010
    917
    189
    0
    Location:
    Clarksburg, MD
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Advanced

    Pics uploaded! Pictures were taken by my cell phone so I appologize for the poor quality photos.

    As you can see, there is a bit of door that is left uncovered toward the bottom. I can see why they mounted it where they did because that is where that body line in the door is. I would have preferred it to be mounted lower and also.... for them to have removed that clear paint protectant vinyl at the bottom of the passenger doors!
     

    Attached Files:

  8. deltron3030

    deltron3030 New Member

    Joined:
    Sep 25, 2009
    437
    64
    0
    Location:
    Lakewood, CA
    Vehicle:
    2010 Prius
    Model:
    II
    Peter, that's a little unfortunate, but the curves on mine also had that odd lining-up problem, but I carefully fit the molding as close to the door edge as I could...I doubt you'll notice in a few weeks....and I hope you don't nick your door too
     
  9. silentak1

    silentak1 Since 2005

    Joined:
    Jul 1, 2005
    893
    28
    0
    Location:
    LA
    Vehicle:
    2010 Prius
    Model:
    III
    Same gap on mine for the curvy part. The bottom part though, the dealer must have chosen to install it slightly higher. The important thing is that both front and rear pieces are horizontally aligned.
     
  10. unkprius

    unkprius Member

    Joined:
    Oct 20, 2010
    152
    18
    0
    Location:
    Texas
    Vehicle:
    2011 Prius
    Model:
    Three
    Just finished installing the trim for my '11. If by chance you have access to a lift so that you could work at eye level it would make the job 100% easier. Ordered from Priuschat Shop, arrived in a little over a week.

    As noted above and I will emphasize more, the door and/or the trim aren't a perfect match either in length or straighness. My passenger rear door is actually smaller than the trim piece length by just a hair. On the front driver's door if I lined up the trim piece on the front door where it is even with the bottom edge of the door at each end, it is almost 3mm high above the bottom edge of the door in the middle. Raising the ends to the installation instruction height left almost 1/4" of paint showing under the bottom middle of the trim on my car. So compromises have to be made in lining things up.

    I gave up trying to run a piece of tape, make marks, etc. while working six inches off the ground. It isn't easy to do. I wound up putting a thin wooden shim (packs are available at any Home Depot etc.) under each end of the door. The shim won't go all the way in, but I wedged it as tight as possible slanted in to the gap under the door, then stuck a 3/4" peel and stick felt pad which I had cut in half and pushed it tight up against the bottom edge of the door so that when the trim rested on the pad/shim it was the correct height at that point. Very quick and easy.

    Then the only item left to do was line it up correctly horizontally. This was tougher, as you are working from a curve at the bottom and have to flip the trim up and down several times, trying to get it to hit at the right spot, and the curved edge makes it a pain. And you can't see both ends at the same time. In the end I eyeballed it and got 3 out of the 4 pieces as close as possible.

    Unfortunately the driver's side door is about 1 mm too far to the right. It's the correct 1mm distance to the edge of the door next to rear door, but with the door/trim discrepancies that leaves a squinch more than 2mm of paint showing at the front edge. It does makes a difference when all other pieces are a better fit. It's not ugly and others I showed it too didn't notice at all, and said it was fine. In the end if it irritates me enough I'll get another set, replace that piece, and sell the others to anyone who messes up their install and need to redo one or more pieces.

    In the end it looks really good, well worth the money. The negative now is that I also purchased the Dawn side molding for the middle of the doors, and with both up(the upper taped on) it looks kind of cluttered, so I'm not sure if I'm going to use it.
     
  11. LovingLife

    LovingLife Junior Member

    Joined:
    Jan 27, 2009
    75
    22
    0
    Location:
    Denver, CO
    Vehicle:
    2010 Prius
    Model:
    III
    I installed mine today, yeah. Turned out to be easier to install than I thought and they do look sharp.
     
  12. erikl

    erikl New Member

    Joined:
    Jun 14, 2010
    36
    10
    0
    Location:
    SF Bay Area
    Vehicle:
    2010 Prius
    Model:
    II
    I've got a set of these in the classifieds, new in the box if anyone's interested!
     
    1 person likes this.
  13. skilbovia

    skilbovia Member

    Joined:
    Oct 25, 2010
    400
    91
    0
    Location:
    Massachusetts
    Vehicle:
    2010 Prius
    Model:
    V
    I bought my Prius V new in October and these moldings were already on the the vehicle. I thought they were standard with the ATP and didn't pay too much attention to it till I started looking around at other Prius V's and didn't see the moldings on any of them. Now I wonder who put them on and why? By the way, they look really nice on Winter Grey Metallic.
     
  14. BhamPrius

    BhamPrius Member

    Joined:
    Jan 19, 2011
    128
    19
    0
    Location:
    Bellingham, WA
    Vehicle:
    2010 Prius
    Model:
    II
    Would love to see your pics of these on the winter grey..I can't wait to put some on mine!
     
  15. peterjmc

    peterjmc Ping pong in Ding Dang...

    Joined:
    Dec 5, 2010
    917
    189
    0
    Location:
    Clarksburg, MD
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Advanced
    I'll snap some pics of mine tomorrow morning :) on Winter Grey they are awesome!
     
  16. skipvan

    skipvan Junior Member

    Joined:
    May 26, 2008
    4
    0
    0
    Location:
    Littleton CO
    Vehicle:
    2010 Prius
    Model:
    Two
    They came on my 2010. Didn't know it was any different until I started reading about them here.

    Skip van
     
  17. BhamPrius

    BhamPrius Member

    Joined:
    Jan 19, 2011
    128
    19
    0
    Location:
    Bellingham, WA
    Vehicle:
    2010 Prius
    Model:
    II
    Lookin' forward to pics for those who have 'em..Winter Grey!
     
  18. Ali

    Ali New Member

    Joined:
    May 9, 2011
    10
    0
    0
    Location:
    Vancouver B.C
    Vehicle:
    2010 Prius
    Model:
    Three
    Gentle Men .
    Ineed two rocker mouldings for my 2010 Prius Right and left one .Toyota part#R 7585147900 AND L #7585247900 .If some one has or know some one who has please let me know. [email protected] or call 604 376 9696
    Thanks.
     
  19. Fla Fla Flo Fly

    Fla Fla Flo Fly Junior Member

    Joined:
    Jan 8, 2011
    38
    3
    0
    Location:
    Illinois
    Vehicle:
    2010 Prius
    Model:
    II
    Has anyone taken any more pictures of these installed on the Winter Grey?
     
  20. peterjmc

    peterjmc Ping pong in Ding Dang...

    Joined:
    Dec 5, 2010
    917
    189
    0
    Location:
    Clarksburg, MD
    Vehicle:
    2012 Prius Plug-in
    Model:
    Plug-in Advanced
    Stock Ride Height with Rotas
    [​IMG]

    Lowered on Eibachs with Rotas
    [​IMG]

    Side angle shot lowered on Eibachs with stock wheels
    [​IMG]
     
    1 person likes this.