1. Attachments are working again! Check out this thread for more details and to report any other bugs.

05 Prius with bad inverter?

Discussion in 'Gen 2 Prius Technical Discussion' started by wiluspyder, Jun 15, 2009.

  1. wiluspyder

    wiluspyder New Member

    Joined:
    May 31, 2006
    16
    1
    0
    Folks,
    I have an 05 Prius and lately it's developed an issue.
    The car has the red triangle on, check engine light on, and under acceleration it seems to hesitate.
    The code that show up on the scanner is:
    P0A78/285: Open or GND short in motor inverter fail (MFIV) signal circuit.
    Possible trouble area (this is from the Prius diagnostic manual):
    - Wire harness or connector
    -w/ converter inverter assembly

    This does look like the inverter is shot.
    Can someone comment on experience with this issue?

    I know there is TSB on this specific issue (EG025-05) and it says to replace the inverter.

    Anyway, thanks for all and any help.
     
    1 person likes this.
  2. northwichita

    Joined:
    Sep 24, 2006
    481
    102
    29
    Location:
    Wichita KS
    Vehicle:
    2004 Prius
    [/i]



    I assume this is continuous from starting, not after long driving /overheating which is a different issue.
    I would be curious and after turning off/ disconnecting the high voltage, (pulling main fuse plug in rear of car; see tech manual), would take off the inverter cover to see if there is any obvious burn/dark burning plastic areas around the inverter( and the wiring that supports it) .
    Note ; I am not a professional and have taken off the cover once, really didn't seem to be big deal, although I was careful not to touch anything. Have fun....
     
  3. richard schumacher

    richard schumacher shortbus driver

    Joined:
    Mar 27, 2004
    7,663
    1,041
    0
    Location:
    United States
    Vehicle:
    2004 Prius
    Model:
    N/A
    It should still be under the hybrid system warranty, in which case you don't want to fool with it yourself lest you void that warranty (or get killed).
     
  4. NortTexSalv04Prius

    NortTexSalv04Prius Active Member

    Joined:
    Nov 14, 2009
    915
    115
    0
    Location:
    Texas
    Vehicle:
    2004 Prius
    Model:
    N/A
    Warranty is based on many fine legal lines drawn in Toyota favor. The Prius is basic toss away after warranty goes.!! Certain componets fall under a limited oem mfg warranty . I doubt that the inverter, trac battery, and transaxle are covered after certain specific time period and mileage odo achievement.
     
  5. 2k1Toaster

    2k1Toaster Brand New Prius Batteries

    Joined:
    Feb 14, 2010
    6,035
    3,855
    0
    Location:
    Rocky Mountains
    Vehicle:
    2006 Prius
    Model:
    Three
    It's only toss-away if you have a salvage title that nobody wants to work on... :rolleyes:
     
  6. richard schumacher

    richard schumacher shortbus driver

    Joined:
    Mar 27, 2004
    7,663
    1,041
    0
    Location:
    United States
    Vehicle:
    2004 Prius
    Model:
    N/A
    "The Prius is basic toss away after warranty goes.!"

    Dang! So now I have to throw away my 2004. Can I get my Jeep Cherokee back? Oh man, that 15 MPG and the electrical fires were sweet.
     
  7. vertex

    vertex Active Member

    Joined:
    Mar 27, 2009
    672
    143
    0
    Location:
    new york
    Vehicle:
    2018 Prius Prime
    Model:
    Prime Plus
    Anyone throwing away a Pri, thow it my way!
     
  8. vertex

    vertex Active Member

    Joined:
    Mar 27, 2009
    672
    143
    0
    Location:
    new york
    Vehicle:
    2018 Prius Prime
    Model:
    Prime Plus
    On a more serious note, before changing the inverter, try this:

    CAUTION:
    Wear insulated gloves before performing the following
    operation.
    (a) Turn the power switch OFF.


    (b) Remove the service plug grip (see page
    HB-154).
    NOTICE:
    Turning the power switch ON (READY) with the service
    plug grip removed could cause malfunction. Therefore,
    never turn the power switch ON (READY) in this state.
    (c) Remove the inverter cover (see page


    HV-531).
    (d) Check the connection condition of the I9 and I10 inverter
    connectors.
    OK:
    Connectors have been connected securely and
    there is no poor connection.
    (e) Reinstall the inverter cover (see page


    HV-538).
    (f) Reinstall the service plug grip (see page
    HB-154).

    Even if the connector is properly mated (which most likely it is). I doubt that gold contacts are used on this connector. Seperate and reconnect the connectors, the wiping action may restore good contact. This is an input signal problem, so it may be repairable without replacing the inverter.